English
5
GENERAL OPERATIONAL PRECAUTIONS
1.
Keep work area clean. Cluttered areas and benches
invite accidents.
2.
Avoid dangerous environment. Don’t expose power
tools and charger to rain. Don’t use power tools
and charger in damp or wet locations. And keep
work area well lit. Never use power tools and
charger near flammable or explosive materials.
Do not use tool and charger in presence of
flammable liquids or gases.
3.
The appliance is not intended for use by young
children or infirm persons without supervision.
Young children should be supervised to ensure
that they do not play with the appliance. All visitors
should be kept safe distance from work area.
4.
Store idle tools and charger. When not in use,
tools and charger should be stored in dry, high
or locked-up place – out of reach of the children
and infirm persons. Store tools and charger in a
place where the temperature is less than 40°C.
5.
Don’t force tool. It will do the job better and safer
at the rate for which it was designed.
6.
Use right tool. Don’t force small tool or attachment
to do the job of a heavy duty tool.
7.
Wear proper apparel. Do not wear loose clothing
or jewelry. They can be caught in moving parts.
Rubber gloves and non-skid footwears are
recommended when working outdoor.
8.
Use eye protection with most tools. Also use face
or dust mask if cutting operation is dusty.
9.
Don’t abuse cord. Never carry charger by cord or
yank it to disconnect from receptacle. Keep cord
from heat, oil and sharp edges.
10.
Secure work. Use clamps or a vise to hold work.
It’s safer than using your hand and it frees both
hands to operate tool.
11.
Don’t overreach. Keep proper footing and balance
at all times.
12.
Maintain tools with care. Keep tools sharp at all
times, and clean for best and safest performance.
Follow instructions for lubricating and changing
accessories.
13.
When the charger is not in use, or when being
maintained and inspected, disconnect its power
cord from the receptacle.
14.
Remove chuck wrenches and wrenches. Form habit
of checking to see that wrenches are removed
from tool before turning it on.
15.
Avoid accidental starting. Don’t carry tool with
finger on switch.
16.
To avoid danger, always use only the specified
charger.
17.
Use only genuine HITACHI replacement parts.
18.
Do not use power tools for applications other than
those specified in the Handling Instructions.
19.
To avoid personal injury, use only the accessories
or attachment recommended in these handling
instructions or in the HITACHI catalog.
20.
Let only the authorized service center do the
repairing. The Manufacturer will not be responsible
for any damages or injuries caused by repair by
the unauthorized persons or by mishandling of
the tool.
21.
To ensure the designed operational integrity of
power tools and charger, do not remove installed
covers or screws.
22.
Always use the charger at the voltage specified
on the nameplate.
23.
Do not touch movable parts or accessories unless
the power source has been disconnected.
24.
Always charge the battery before use.
25.
Never use a battery other than that specified. Do
not connect a usual dry cell, a rechargeable battery
other than that specified or a car battery to the
power tool.
26.
Do not use any transformer that has a booster.
27.
Do not charge the battery from an engine electric
generator or DC power supply.
28.
Always charge indoors. Because the charger and
battery heat slightly during charging, charge the
battery in a place not exposed to direct sunlight;
where the humidity is low and the ventilation is
good.
29.
Before starting to work in a high place, pay
attention to the activities below to make sure
there are no people below.
30.
Use the exploded assembly drawing on this
handling instructions only for authorized servicing.
31.
If the supply cord is damaged, it must be replaced
by the manufacture or its service agent or a
similarly qualified person in order to avoid a
hazard.
PRECAUTIONS FOR CORDLESS OIL PULSE
DRIVER
1.
This is portable tool for tightening and loosenig
wood screws. Use it only for these operation.
2.
Use the earplugs if using for a long time.
3.
One-hand operation is extremely dangerous; hold
the unit firmly with both hands when operating.
4.
After installing the driver bit, pull lightly out the
bit to make sure that it does not come loose. If
the bit is not installed properly, it can come loose
during use, which can be dangerous.
5.
Use the bit that matches the screw.
6.
Tightening a screw with the oil pulse driver at an
angle to that screw can damage the head of the
screw and the proper force will not be transmitted
to the screw. Tighten with this oil pulse driver
lined up straight with the screw.
7.
Always charge the battery at a temperature of 0
– 40°C.
A temperature of less than 0°C will result in over
charging which is dangerous. The battery cannot
be charged at a temperature greater than 40°C.
The most suitable temperature for charging is that
of 20 – 25°C.
8.
Do not use the charger continuously.
When one charging is completed, leave the charger
for about 15 minutes before the next charging of
battery.
9.
Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
10.
Never disassemble the rechargeable battery and
charger.
11.
Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great
electric current and overheat. It results in burn or
damage to the battery.
12.
Do not dispose of the battery in fire.
If the battery burnt, it may explode.
13.
Do not insert object into the air ventilation slots
of the charger.
Inserting metal objects or inflammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
14.
Bring the battery to the shop from which it was
purchased as soon as the post-charging battery
life becomes too short for practical use. Do not
dispose of the exhausted battery.
15.
Using an exhausted battery will damage the
charger.
Summary of Contents for WP 12DM
