Hitachi ZW 370-6 Operator'S Manual Download

Page: 228 / 450

3-8

OPERATING THE ENGINE

Starting in Cold Weather

Preheating

1. Turn key switch (1) ON. The ambient temperature

sensor is activated so that the engine is automatically

preheated.

2. Preheat indicator (2) should turn ON. As long as the

preheat indicator stays ON, the engine is being heated.

NOTE: Preheating time varies depending on the

ambient

temperature.

NOTE: If your machine is equipped with the optional

joystick steering, turn ON the joystick steering system switch

after turning key switch (1) to ON position. Otherwise, the

machine cannot move forward/reverse.

Refer to the previous page.

3. As soon as preheat indicator (2) turns OFF, turn key

switch (1) to START position to rotate the starter. As

soon as the engine starts, release the key switch. The

key switch will automatically return to the ON position.

Run the engine at low idle without applying

accelerator pedal (3).

IMPORTANT: At starting the engine, the engine RPM

(min

-1

) is kept at low idle for maximum 35 seconds

to warm up the coolant, hydraulic oil, etc. After this

period, the engine RPM will increase by applying the

accelerator pedal (3).

WARNING: Do not operate the machine while the

engine RPM is being kept at low idle, otherwise, the

machine or the front attachment could unexpectedly

move that may result in serious injury.

4. Perform checks to be done after starting the engine by

referring to the following section.

NOTE: Headlights, working lights or room light may

become dim during engine preheating in the cold

environment.

M4GB-01-089

MNEC-01-073

MNEC-01-036

Summary of Contents for ZW 370-6



































































































































































































































































































































































































































































Search results

Summary of Contents for ZW 370-6

Reviews:

Related manuals for ZW 370-6

Brands by name

Popular brands

Hitachi ZW 370-6, Operator'S Manual

Search results

Summary of Contents for ZW 370-6

Reviews:

Related manuals for ZW 370-6

Brands by name

Popular brands