manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at 88.208.23.73:8080, and optimize your productivity and performance on the field.

Share
Download
background image

MAINTENANCE

7-82

Electrolyte Level Check
--- every 100 hours (Do this when machine is cold.)

1.  Check the electrolyte solution level at least once a 

month. 

2.  Park the machine on level ground and stop the 

engine.

3.  Check the electrolyte solution level.

3.1  When checking the level from the battery side: 

Clean around the level check lines with a wet 

towel. Do not use a dry towel. Static electricity 

may spark, causing the battery gas to explode. 

Check if the electrolyte solution level is between 

U.L (Upper Level) and L.L (Lower Level). In case the 

electrolyte solution level is lower than the middle 

level between the U.L and L.L, immediately refill 

with distilled water or commercial battery fluid. Be 

sure to refill with distilled water before recharging 

(operating the machine). After refilling, securely 

tighten the filler caps.

3.2  When impossible to check the level from the 

battery side or no level check mark is indicated on 

the side: 

After removing the filler plug from the top of the 

battery. Check the electrolyte solution level by 

viewing through the filler port. Use a flash light and 

a mirror to do this. It is difficult to accurately judge 

the electrolyte solution level in this case. Therefore, 

when the electrolyte solution level is flush with the 

U.L, the level is correct. Referring to the illustrations 

to the right, check the level. 

 

When the electrolyte solution level is lower than 

the bottom end of the sleeve, refill with distilled 

water or commercial battery fluid up to the bottom 

of the sleeve. Be sure to refill with distilled water 

before recharging (operating the machine). After 

refilling, securely tighten the filler caps.

3.3  When an indicator is available to check the level, 

use it.

4.  Always keep the battery areas clean to prevent 

battery discharge. Check terminals for looseness and/

or corrosion. Coat terminals with grease or petroleum 

jelly to prevent corrosion build up.

U.L (Upper Level)
L.L (Lower Level)

Upper Level
Lower Level

Filler Port

Sleeve

Separator Top

Correct

Lower

Since the electrolyte solution surface touches the bottom 

end of the sleeve, the electrolyte solution surface is raised 

due to surface tension so that the electrode ends are seen 

curved.

When the electrolyte solution surface is lower than the 

bottom end of the sleeve, the electrode ends are seen 

straight.

M409-07-072

M146-07-109

M146-07-110

M146-07-111

M146-07-112

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Buhler 2895E Operator And Parts Manual preview
2895E
Brand: Buhler Pages: 46

Brands by name

Popular brands

Load more brands