Hitachi ZW 550-6 Operator'S Manual Download

Page: 431 / 438

14-1

ZW550-6 US

INDEX

24 V DC Electrical Outlet ..........................................................1-114

2nd/3rd Speed Limit Switch (Option) .................................1-105

Accelerator Pedal ..........................................................................1-90

Accelerator Pedal Operation, Check ....................................7-114

Accumulator Function, Gas Leakage, Looseness, and

Damage, Check ........................................................................7-92

Adjust Operator’s Seat ...................................................................S-6

Adjusting Drive Belt .....................................................................7-74

Adjusting Operator’s Seat (Air Suspension Type Seat) ..1-123

Adjustment of Bucket Angle Switch .........................................5-8

Adjustment of Bucket Auto Leveler ..........................................5-6

Adjustment of Dual Lift Arm Auto Leveler ..........................5-10

After Operation, Precaution .....................................................5-26

After Starting, Check ......................................................................3-9

Aftertreatment Device .......................................... 1-3, 7-104, S-36

Aftertreatment Device Manual Regeneration ...................5-13

Aftertreatment Device Regeneration ...................................1-34

Aftertreatment Device Regeneration Inhibited ................1-57

Aftertreatment Device Regeneration Status Display ......1-34

Aftertreatment Device Regeneration Switch ...................1-108

Aftertreatment Device, Check and Clean ..........................7-104

Air Bleeding Procedure, Fuel System.....................................7-60

Air Breather Element, Replace .................................................7-50

Air Cleaner ......................................................................................7-71

Air Cleaner Element, Replace ...................................................7-71

Air Conditioner ..............................................................................7-99

Air Conditioner, Check ..............................................................7-101

Air Conditioner, Components Name ...................................1-116

Air Conditioner, Controller Part Name and Function ....1-117

Air Conditioner, Feature ...........................................................1-115

Air Conditioner Compressor Belt, Check ...........................7-102

Air Conditioner Condenser, Check .......................................7-102

Air Conditioner Filters, Clean/Replace ..................................7-99

Air Conditioner ON/OFF Switch ............................................1-118

Air Conditioner Piping, Check ................................................7-101

Air Conditioner Receiver Dryer, Replace ............................7-103

Air Conditioner Usage ..............................................................1-122

Air Filter Restriction Indicator (Red) .......................................1-16

Air Pressure, Check .......................................................................7-94

Air Suspension Type Seat ........................................................1-123

Air Suspension Type Seat, Components Name ...............1-123

Alarm Occurrence Screen ..........................................................1-27

Alternator, Check and Clean ...................................................7-116

Armrest Adjust Handle .............................................................1-102

Articulation Lock..............................................................................7-8

Articulation Stopper .......................................................1-137, S-38

Asbestos .......................................................................................... S-33

Ash Tray ..........................................................................................1-114

Auto Air Conditioner .................................................................1-115

Auto Brake .......................................................................................4-20

Auto Idling Stop ................................................................. 1-53, 5-11

Auto Idling Stop, Acting Time Setting ..................................1-54

Auto Idling Stop, ON/OFF ..........................................................1-53

Auto Idling Stop Operating Condition .................................5-12

Auto Transmission, Shift Range ..................................................4-5

Automatic Regeneration .............................................................1-5

Automatic regeneration (Auto-regeneration) ...................1-35

Auxiliary Control Lever (Option) ...........................................1-101

Avoid Accidents from Backing Up and Turning ................ S-16

Avoid Applying Heat to Lines Containing Flammable

Fluids ........................................................................................... S-32

Avoid Heating Near Pressurized Fluid Lines ....................... S-31

Avoid High-Pressure Fluids ....................................................... S-28

Avoid Injury from Rollaway Accidents .................................. S-15

Avoid Operation with Loads on Only One Side .................5-17

Avoid Overloading .......................................................................5-17

Avoid Positioning Bucket or Attachment Over

Anyone........................................................................................ S-17

Avoid Power Lines ........................................................................ S-19

Avoid Rapid Steering Changes and/or Sudden

Braking ........................................................................................5-17

Avoid Tipping ................................................................................. S-17

Axle Oil .............................................................................................7-16

Axle Oil, Change ............................................................................7-37

Axle Oil Cooler Fins (Option), Clean .......................................7-40

Axle Oil Cooler Line Filter (Option), Replace .......................7-39

Axle Oil Level, Check ...................................................................7-35

Axle Support Mounting Bolts, Retighten...........................7-118

Backup Alarm, Check ..................................................................7-85

Basic Screen ....................................................................................1-21

Batteries ...........................................................................................7-80

Batteries, Replace .........................................................................7-84

Battery Disconnect Switch ......................................................1-135

Battery Disconnect Switch Operation ................................1-136

Before Operation ..........................................................................5-16

Before Starting, Check ...................................................................3-3

Beware of Asbestos and Silicon Dust and Other

Contamination ......................................................................... S-33

Beware of Exhaust Fumes.......................................................... S-31

Biodiesel Fuel .................................................................................7-57

Bleed Air from the Fuel System ...............................................7-60

Bleed Air from the Hydraulic System ....................................7-45

Booster Batteries...........................................................................3-10

Brake Oil Low Pressure Indicator (Red) .................................1-13

Brake Pedal .....................................................................................1-90

Brake Performance, Check ........................................................7-88

Brake System ..................................................................................7-88

Break-in Period for New Machine ..............................................2-1

Brightness Adjustment ...............................................................1-42

Bucket Angle Switch, Adjustment .............................................5-8

Bucket Auto Leveler, Adjustment ..............................................5-6

Bucket Control Lever ...................................................................1-97

Bucket Teeth, Check ..................................................................7-111

Cab ...................................................................................................1-128

Cab, Check ....................................................................................7-112

Cab Door ........................................................................................1-133

Cab Features ......................................................................................1-7

Cab Heater Operation ...............................................................1-119

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands