Hitachi ZW 550-6 Operator'S Manual Download

Page: 49 / 438

SAFETY

S-37

Precaution for Communication Terminal

Equipment

This machine has a communication terminal equipment

emitting electrical waves installed inside the rear tray situated

at the back of the operator's seat. There is a possibility that

a medical device, including an implantable device such as a

cardiac pacemaker, could be affected and malfunction due to

the electrical waves emitted from the communication terminal

equipment.

Any person fitted with a medical device such as the above

should not use this machine, unless the medical device and

the rear tray are at least 22 centimeters (8.662 inches) apart

at all times. If this condition cannot be met, please contact

your authorized dealer and have the person in charge stop

the communication terminal equipment from functioning

completely and confirm that it is not emitting electrical waves.

This machine is equipped with a communication terminal type

A or type B.

Consult your authorized dealer for the type of communication

terminal.

Specific Absorption Rate ("SAR") (measured by 10 g per unit) of

communication terminal equipment:

Type A

Type B

E-GSM900

0.573 W/kg (914.8 MHz)

0.12 W/kg (897.6 MHz)

DCS-1800

0.130 W/kg (1710.2 MHz)

0.06 W/kg (1748.0 MHz)

WCDMA Band

0.271 W/kg (1950.0 MHz)

0.05 W/kg (1950.0 MHz)

WCDMA Band

VIII

0.10 W/kg (892.6 MHz)

NOTE: Please contact to your authorized representative

if you want to know which terminal model A or B is installed.

* This data was measured by having each type of

communication terminal equipment, such as the

communication terminal equipment used with this machine,

and a human body set apart by 3 cm (1.18 inches).

* SAR is a measure of the amount of radio frequency energy

absorbed by the body when using a wireless application such

as a mobile phone.

* In the United States, the SAR limit set by the Federal

Communications Commission is at or below 1.6 watts per

kilogram (W/kg) taken over the volume containing a mass of 1

gram of tissue that is absorbing the most signal.

90MNEC-01-046

Machine Front

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands