background image

p10

p11

section 3

section 2

The quadcopter includes the flight control system and an airborne camera that are convenient to use. 

quadcopter battery

quadcopter preparation

Battery Specifications:

Type

Li-Po Battery

Capacity
Charging Ambient Temperatures
Discharging Ambient Temperatures
Charging/Discharging Ambient Relative Humidity

5300mAh
0°C to 50°C
-20°C to 50°C
< 80%

Before using the battery, please carefully read and strictly comply with this manual’s instructions. Any problems 
caused due to failure to follow instructions will be the responsibility of the user.
Charging the Quadcopter Battery:

1. Connect the charger to an AC power source (110-240V, 50 / 60Hz). If necessary, please use a power adapter.
2. While charging, the battery charger indicator lights up, and turns red.
3. When the battery indicator turns green, it means the battery is fully charged. Please remove the battery and 
disconnect the charger cable from the socket once the battery is completely charged. Do not leave the battery 
plugged in to the charger for long periods of time after the light has turned green.

Figure 5

Installing the Quadcopter Battery:

Push the battery in the correct direction (Figure 6) into the quadcopter’s battery compartment and ensure 
the battery is properly installed before fastening the battery lock. If the battery lock is not fastened before the 
flight, it may cause poor contact with the battery which may affect flight safety or even cause the quadcopter 
to fail to take off. 

Figure 6

Functions

Master Controller
GPS & Compass
Indicators

Core of flight control system. Connects all modules and plays the role of centralized control.
Used for positioning and navigating the quadcopter.
Indicates current status of flight control system. Used to navigate during night flying.

Flight Control System Component Modules

Flight Control System:

The Q-Cop 450 is designed with an AEE flight control system, which is easy to operate and provides stability. 
In addition to supporting basic flight maneuvers such as climb, descend, roll and pitch, it also supports failsafe 
protection, battery alarm levels, smart direction control and other functions. 

Rotor Blades

Camera Lens
Micro SD

Card Slot
Undercarriage

Motor

Front Indicator

Power Switch

Battery Level Display
Battery Level 

Check Button

Quadcopter

Batteries

Rear Indicator

Tail Indicator

Summary of Contents for AEE Q-COP 450

















Reviews: