HITROL HT-100F Series Instruction Manual Download | Manualshive

Page: 12 / 12

background image

HT-100F Series

HITROL CO., LTD.

12

Warranty
and
Contact

Warranty and Service

This product is subject to a two-year warranty after shipment, and any unpaid service

will be provided for any damage found under normal operating conditions. If it is not

related to product failure, the service charge will be payable. You can request A/S at

our website or by contacting our headquarters.

Headquarters / Factory / Research Center

Address: HITROL CO., LTD., 141, Palhakgol-gil, Jori-eup, Paju-si, Gyeonggi-do, Korea

TEL.: 031-950-9700 (Headquarters and A/S)

FAX: 031-943-5600 (Headquarters and A/S)

«
...
10
11
12

Summary of Contents for HT-100F Series













Reviews:

No comments

Related manuals for HT-100F Series

Brand: Nautel Pages: 62

Brand: Nautel Pages: 56

Brand: Nautel Pages: 48

Brand: Ocean Signal Pages: 2

Brand: Q5X Pages: 2

Brand: RKI Instruments Pages: 65

Brand: Icom Pages: 16

Brand: ADTRAN Pages: 24

Warrior HHMS-9XW08

Brand: Cervis Pages: 19

Brand: WAC Lighting Pages: 6

Brand: Radionode Pages: 20

AERASGARD KLQ-W Series

Brand: S+S Regeltechnik Pages: 16

Brand: H-ITT Pages: 2

Brand: UIS Pages: 4

Brand: SGM LEKTRA Pages: 4

Brand: Ningbo Pages: 11

Brand: Jung Pages: 15

Brand: Kenwood Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands