background image

For the HKS Lazar (please tear off and sent to the HKS Lazar).

HKS Lazar sp. z o.o.

ul. Wodzisławska 15 B
44-335 Jastrzębie Zdrój
tel. +48 32 472 95 78

www.hkslazar.pl

Warranty Card and confirmation of quality and completeness of the boiler

Holz Master

(HM 20* - 

*delete what does not apply

)

Serial number of the boiler ..................................................................... Output ..................................

User (Surname, name) 

.......................................................................................................

Address (street, town, zip code) 

.......................................................................................................

Tel / Fax

.......................................................................................................

Boiler thermal protection*:

four-way mixing valve with actuator

* - delete what does not apply

thermostatic valve TV 65 / Hydraulic Kit

The setup of the controller shall be completed by an authorised service partner of HKS Lazar.
The completeness including the accessories has been warranted by HKS Lazar.

Unfilled Warranty Card is void.

Measurement

Value

Chimney draft

(Pa)

Exhaust temperature (°C)
Volume of the boiler room

(m

3

)

Intake ventilation cross-section (cm

2

)

The user confirms what follows:

1. The boiler has not revealed any defects during the launch performed by the service partner;
2. He received the Operation and installation manuals of the Smart Fire boiler with the filled Warranty Card and 

confirmation of quality and completeness of the boiler;

3. He was instructed in operation and maintenance of the boiler heating system.

 ............................................

Manufacture date

...........................................

Company Stamp

............................................

Service inspection (signature)

...........................................

Installation date

...........................................

Service partner

(stamp, signature)

............................................

Name, address, date, user 

signature

The customer, the installing party and the service partner confirm their consent for processing of their personal data for the purpose of the system  

maintenance as required by the  Ustawa z dnia 29/08/1997 o Ochronie Danych Osobowych Dz.U.Nr133poz 883. [Personal data act]

Holz Master Manual

wer. 22/05/2012/EN/V1.0

HKS LAZAR 

str.40

Summary of Contents for Holz Master










































Reviews: