95
Bosch operating instructions
Battery charge indicator
The five green LEDs on the battery charge indicator
(3)
in-
dicate the battery's state of charge of when the battery is
switched on.
Each LED represents approximately 20% of the charging ca-
pacity. When the battery is fully charged, all five LEDs will be
lit.
The battery's state of charge when switched on is also shown
on the display of the on-board computer. Read and follow
the instructions in the operating manuals for the drive unit
and on-board computer.
If the battery capacity is less than 5%, all the LEDs on the
battery charge indicator
(3)
on the battery will go out. The
display function of the on-board computer, however, will
carry on working.
Once charging is complete, disconnect the battery from the
charger and the charger from the mains.
Using two batteries for one eBike (optional)
The manufacturer can also equip an eBike with two batter-
ies. In this case, one of the charging sockets will not be ac-
cessible or it will have been sealed with a sealing cap by the
bicycle manufacturer. Only charge the batteries via the char-
ging socket that is accessible.
u
Never open charging sockets that have been sealed by
the manufacturer.
Charging batteries via a charging
socket that used to be sealed may cause irreparable dam-
age.
If you want to use an eBike that is designed for two batteries
with only one battery, cover the contacts of the unused
socket using the cover
(10)
provided. Otherwise there is a
risk that the exposed contacts will cause a short circuit (see
figures A and B).
Charging process for two batteries
If two batteries are fitted to an eBike, both batteries can be
charged using the uncovered connection. To begin with,
both batteries are charged one after the other until they
reach approx. 80–90% capacity, then they are both charged
at the same time until full (the LED flashes on both batter-
ies).
When the bike is in operation, power is drawn from both bat-
teries on an alternating basis.
If you take the batteries out of the holders, you can charge
each one individually.
Charging with one battery fitted
If only one battery is fitted, you can only charge the battery
that has the accessible charging socket on the bike. You can
only charge the battery with the sealed charging socket if
you take the battery out of the holder.
Inserting and removing the battery
u
Always switch off the battery and the eBike system
when inserting the battery into the holder or remov-
ing it from the holder.
Inserting and removing the standard battery (see figure
A)
In order for the battery to be inserted, the key
(5)
must be
inserted into the lock
(6)
and the lock must be open.
To
insert the standard battery
(8)
, place it onto the con-
tacts on the lower holder
(9)
on the eBike (the battery can
be titled towards the frame by up to 7°). Tilt it into the upper
holder
(7)
as far as possible until you hear it click into place.
Check that the battery is secure in all directions. Always se-
cure the battery by closing the lock
(6)
– otherwise the lock
may open and the battery may fall out of the holder.
Always remove the key
(5)
from the lock
(6)
after closing it.
This prevents both the key from falling out and the battery
from being removed by unauthorised third parties when the
eBike is not in use.
To
remove the standard battery (8)
, switch it off and open
the lock using the key
(5)
. Tilt the battery out of the upper
holder
(7)
and pull it out of the lower holder
(9)
.
Inserting and removing the rack-mounted battery (see
figure B)
In order for the battery to be inserted, the key
(5)
must be
inserted into the lock
(6)
and the lock must be open.
To
insert the rack-mounted battery
(2)
, slide it contacts-
first into the holder
(1)
on the rack until you hear it click into
place.
Check that the battery is secure in all directions. Always se-
cure the battery by closing the lock
(6)
– otherwise the lock
may open and the battery may fall out of the holder.
Always remove the key
(5)
from the lock
(6)
after closing it.
This prevents both the key from falling out and the battery
from being removed by unauthorised third parties when the
eBike is not in use.
To
remove the rack-mounted battery (2)
, switch it off and
open the lock using the key
(5)
. Pull the battery out of the
holder
(1)
.
Removing the PowerTube battery (see figure C)
❶
To remove the PowerTube battery,
(15)
open the lock
(6)
using the key
(5)
. The battery will be unlocked and
fall into the safety restraint
(14)
.
❷
Press on the safety restraint from above. The battery
will be unlocked completely and fall into your hand.
Pull the battery out of the frame.
Note:
As a result of
varying
designs, the battery may need
to be inserted and removed using a different method. In this
case, consult the bicycle documentation provided by your
bicycle manufacturer.
Inserting the PowerTube battery (see figure D)
In order for the battery to be inserted, the key
(5)
must be
inserted into the lock
(6)
and the lock must be open.
❶
To insert the PowerTube battery
(15)
, place it so that
its contacts are in the lower holder of the frame.
❷
Push the battery upwards until it is held by the safety
restraint
(14)
.
English –
3
Bosch eBike Systems
0 275 007 XPX | (23.04.2018)
Summary of Contents for CD1 Cargo
