2
CONTROL PANEL
MOUNTING SPECIFICATIONS
1. Engine Control Switch allows for engine speed
selection. In Run/Idle position, engine runs at idle
speed at no load, and weld/power speed under load.
2. Engine Choke Control. Use control to change engine
air/fuel mix.
3. Engine Hour Meter. Combined with the Fastex “no
tools” oil change feature, routine service is easily
monitored and performed.
4. Amperage Control. Easy to set up for welding, and the
amperage control does not have to be turned up to
maximum to gain full auxiliary output.
5. Amperage Selection Chart. Explains weld settings for
typical electrode diameter sizes and types.
6. 120/240 Volt Receptacle. This versatile, 50-amp
circuit-breaker-protected receptacle can supply up to
10,000 watts of 230-volt power or, up to 10,000 watts of
120-volt power through two separate 120-volt circuits.
(Note: Protective covers not shown.)
7. 120 Volt Receptacle. Protected by two 20-amp
circuit breakers.
Champion 10,000
10,000-WATT AUXILIARY POWER GENERATOR • 230-AMP DC/CC WELDER
AMPERAGE ADJUST
ENGINE
AC POWER: TOTAL ALL LOADS 10,000 WATTS
MADE IN
GND/PE
120 V / 240 V
START
RUN
RUN / IDLE
OFF
CHOKE
3/32
1/8
5/32
3/16
5/64
3/32
1/8
5/32
3/16
3/32
1/8
5/32
3/32
1/8
5/32
3/32
1/8
5/32
3/32
1/8
5/32
3/32
1/8
5/32
ELECTRODE
DIAMETER
50
10
0
15
0
200
AMPERAGE
RANGE
6010
&
6011
6013
7014
7018
7024
Ni-Cl
308L
MAX
MIN
80
100
120
140
160
180
200
220
PERFORMANCE DATA
Fuel Consumption Data
The Champion 10,000 offers modern, fuel
efficient engines from Robin or Kohler. With
the OHV design, automatic idle and 10 gallon
fuel tank, you can expect to put in long hours
before having to stop and refuel. For example:
• Welding at 125 amps, 100% duty cycle,
uses about 1 gal of fuel every hour.
• While not welding, the engine drops to idle
speed using about 1/2 gal of fuel every hour.
• On a typical job using 1/8-in 7018 electrodes
(125 amps, 20% duty cycle) you can expect
over 16 hours of operation.
• Under a continuous load of 4,000 watts
of auxiliary power, the Champion 10,000
would run for about 9 hours.
A. 18 in (457 mm)
B. 16-9/16 in (421 mm)
C. 3/4 in (19 mm)
D. 3 in (76 mm)
E. 31-1/2 in (800 mm)
F. 37-1/2 in (953 mm)
G. 13/32 in (10 mm) Diameter
4 Holes
Engine End
G
A
B
C
D
E
F
Typical Power Requirements for Farm, Home and Contractor Equipment
Rating
14 in
1-1/2 HP
2 HP, 14 in
HID
Metal Halide
Mercury
Vapor
400 gph
900 gph
1 HP
1.7 HP
Equipment
Band Saw
Air Compressor
Electric Chain Saw
Flood Lights
Submersible Pump
Centrifugal Pump
High Pressure Washer
Wet & Dry Vac
Starting
Watts
2500
8200
1100
125
313
1000
1250
600
900
6100
900
Running
Watts
1100
2200
1100
100
250
—
1000
200
500
1600
900
Rating
1/2 HP
1/3 HP
1-1/2 HP
550 PSI
700 PSI
1/3 HP
1/2 HP
1/2 in
8-1/4 in
10 in
Starting
Watts
3400
1720
8200
4500
6100
2150
3200
600
1400
6300
Running
Watts
1000
720
2200
1400
1600
750
1050
600
1400
1800
Equipment
Portable Conveyor
Farm-Duty Motors Std.,
(e.g. Conveyors, Feed
Augers, Air Compressors)
Washer 2 gal/min
2 gal/min
Refrigerator or Freezer
Sump Pump
Hand Drill
Circular Saw
Table Saw
