Hobart 6921 Series Operation And Maintenance Manual Download | Manualshive

Page: 7 / 262

background image

Introduction

1. General

The following information is provided for the operator to familiarize himself with using the manual
properly. THE MANUAL MUST BE READ AND UNDERSTOOD BEFORE PERSONNEL ATTEMPTS
TO OPERATE, INSTALL, OR REPAIR THIS EQUIPMENT.

2. Scope

The manual covers a series of synchronous Motor-Generator Sets identified by the Specification
Numbers listed. A detailed description of the equipment and information covering operation,
maintenance, troubleshooting, repair, and overhaul is included.

3. Purpose

The manual provides information and instructions to guide and assist operator and maintenance
personnel in the proper use and maintenance of the equipment.

4. Contents

The Introduction is a List of Effective Pages which lists each page in the manual by its Chapter/Section,
and page number. Directly opposite each page number listing is a date which indicates whether the
page is original or revised.

The Table of Contents contains a list of all Chapters, Sections, and the principal paragraph titles within
each Section. The location of each listing is identified by Chapter/Section and page number. A
complete list of illustrations with their location is provided at the end of the Table of Contents.

The main text of the manual is divided into four Chapters as follows:

Chapter 1. Description/Operation

Chapter 2. Servicing

Chapter 3. Troubleshooting

Chapter 4. Illustrated Parts List

Each Chapter is divided into as many Sections as necessary. Sections are referred to by a combination
Chapter/Section number. Example, 2-3 refers to Chapter 2, Section 3.

5. Format

a. Paragraphing and Outlining

The material within each Section is divided into main subjects with applicable paragraph headings
and sub-headings as required. This method provides a means of identifying material for reference
purposes. For example;

(1)

Control

a. A. Interior Panel

•

(1) Protective devices

•

(a) Overload relay

•

(2) Contactors

OM-2040 / Operation and Maintenance Manual

90D20 / Generator Sets

February 28/94 Revised

Introduction

Page 1

«
...
5
6
7
8
9
...
»

Summary of Contents for 6921 Series







































































































































































































































































Reviews:

No comments

Related manuals for 6921 Series

Brand: JBL Pages: 11

Brand: Sven Pages: 6

Brand: Garland Pages: 120

Brand: GPX Pages: 16

Brand: Paso Pages: 30

Brand: GENERGY Pages: 90

Brand: Sangean Pages: 1

Brand: Steelcase Pages: 2

Brand: Lloyd's Pages: 24

Brand: PortaCo Pages: 28

Brand: Tesla Pages: 53

Brand: Zebronics Pages: 7

Brand: Curtis Pages: 29

Brand: Boston Acoustics Pages: 2

Brand: AudioSource Pages: 8

Brand: VIETA Pages: 22

Brand: Mi-T-M Pages: 94

Brand: Mi-T-M Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands