Please read the instructions for the radio system carefully before running your car.
The servo is required to be set at Center position before starting assembly. To set the servo at the Idle
(Neutral) position switch on the transmitter and receiver. Allow the servo trim arm at Center position,
and turn off the transmitter then the receiver.All debug operations are complete, and the servo is in the
Middle position that you expect.
A.Neutral
B.Brake
/Speed down
C.Forward
/Speed up
Throttle Trigger
C.Right
Steering Wheel
A.Neutral
B.Left
1.Push the trigger forwards to allow the
vehicle to speed down to brake.
2.Pull the trigger backwards to allow the
vehicle to go forward and speed up.
Turn the steering wheel to
the left or right to let the
vehicle turn left or right.
The 1/5th transmitter has two different setting way.Push up the power button,will
enter
into common function set.Press the mode fuction key while pushing up the power button,
up the power button,will enter into the system function set.
Switch on the transmitter,then the
receier to start the engine;turn off
the receiver then the transmitter
to stop running engine.
04
Use Transmitter to control your Vehicle...
The function switches on the transmitter:
1.Antenna
LCD
2-Channel
(
FM)
#TR80127
1/5th scale Gasoline powered RTR model Transmitter has 2 styles,
Transmitter
(
AM)
.
you can choose it.Below is the LCD Transmitter(FM) function description
.
LCD
Transmitter
(
FM)
&
Multifunctional
6.Power switch on(push up)
Power switch off(push down)
7.Working Indicator
3.Four function Key:
Mode Channel
Increase Decrease
4.Throttle Trigger
8.Steering Wheel
2.Switch key
5.T1/T2/T3/T4:
Shortcut key
2
3
4
5
5
5
6
7
8
1.The throttle trigger and steering wheel must be in netural position before reading the figure.
2.EPA:
a.EPA-ST : front wheel steering set b.EPA-TH:brake or forwarding operation set.
3.SPD:
a.SPD-TN: steering speed set b.SPD-RN:return to netural position set
4.EXP:(sensibility adjustable range:-100%~+100%;-100% is low-grade,+100% is superior.)
a.EXP-ST:steering sensibility set. b.EXP-FW:forward sensibility set
c.EXP-BK:brake sensibility set.
7.BMX: brake function mix set
8.TRM:(idle position adjust)
a.TRM-ST:steering trim set b.TRM-TH:forward trim set
9.D/R
a.D/R steering rate set b. D/R-ST:steering angle set
10.ATL
a.brake intensity set b.ATL-BK:set the brake intensity solely(adjusting brake servo angel)
11.SBT:(two channel idle position set)
a.SBT-ST:steering trim set b.SBT-TH:forward trim set
12.REV:
a.REV-ST:steering reverse set(off/on) b.REV-TH:forward reverse set(off/on)
13.MODE SEL:can save 10 models control data.
1.Copy mode control data
2.Mode control data initialization
3.Each mode control data name set.
4.Signal output set(PPM mode only)
5.FNC-SW2:switch key
6.FNC-DT:
a.ST:steering trim adjust b.TH:throttle trim adjust
c.DR:steering control rate DR-ST adjust
d:AT:ATL-BK adjust
e.E1:steering EXP-ST adjust f.BK:BMX-RT adjust
7.LED-MD:LED bright adjustment.press the increase or decrease to change light brightness.
6.ACC:
a.ACC-FW:add forward speed set b.ACC-BW:add brake speed set
5.ABS:(anti-slip brake set)
a.ABS-PT:brake return speed set. b.ABS-CY:perform cycle set
c. ABS-DL:extend brake time set d.ABS-MD:off or on set
4
be fully extended
Make sure antenna is properly
inserted and screwed in
the transmitter.Antenna should
1
LCD
Transmitter
(
FM)Function Description:
Battery Precaustions:
1.In order to keep continue better performance under
operations, we strongly recommend you to use the
1.5V alkaline batteries instead of the 1.2 V chargeable
batteries.eight AA battery should be inserted on the
bottom of the transmitter.
2.The batteries may leak in the event that they are
installed with wrong polarities.
3.Do not use batteries of different types.
4.Do not leave the batteries if not in use for long periods.
Multifunctional
2-Channel
(
AM)
#TR80126
Common Function Setting:
System Function Setting:
2-Channel Radio Transmitting System
3
