background image

Warranty

AquaCraft

will warrant this kit for 90 days after the date of purchase from defects in materials or workmanship. 

AquaCraft

will either repair or replace, at no charge, the incorrectly made part.

Make sure you save the receipt or invoice you were given when you bought your model! It is your proof of purchase and we
must see it before we can honor the warranty.

To return your Kings Ransom for repairs covered under warranty you should send it to the below address.

Hobby Services 

3002 N. Apollo Drive, Suite 1

Champaign, Illinois 61822

Attn: Service Department

Phone: (217) 398-0007 9:00 am – 5:00 pm Central Time M-F

E-mail: 

hobbyservices@hobbico.com

Thank you for purchasing Aquacraft’s Kings Ransom Pirate Ship. This manual contains the instructions
you need to safely prepare, operate, and maintain your R/C boat. Read over this manual thoroughly
before operating your ship.

If for any reason you feel this model is not for you, return it to your local dealer immediately. 

PLEASE NOTE

: Your hobby dealer can not accept a return on any model boat after the assembly

sequence has begun.

AQUZ1002 for AQUB58**

Entire Contents © Copyright 2006

ASSEMBLY AND OPERATION MANUAL

by

Summary of Contents for King's Ransom













Reviews: