background image

4

RECOMMENDED ACCESSORIES

This is a partial list of items required to finish the Midi Edge 
540 that may require planning or decision-making before star-
ting to build. Order numbers are provided in parentheses.

 

1 x Motorset FW 2840 Order No: FWLA8001

 

1x or motor set Speed Order No: FWLA8002

 

4 x Servos Order No: TACM0210

 

1 x Lipo-battery 3s 1300 mAh 30C Order No: GPMP0840 
for moto set 2840

 

1x Lipo-battery 3s 1600 mAh 30C Order No: GPMP0850 
for motor set Speed

 

1 x 6 channel receiver Order No: TACL0624

 

4 x Servo wire extension Order No: HCAQ7310

ADHESIVES AND BUILDING SUPPLIES

In addition to common household tools and hobby tools, this 
is the “short list” of the most important items required to build 
the Midi Edge 540. Great Planes Pro™ CA and Epoxy glue are 
recommended.

 

· Hobby knife

 

· Philips screw driver

 

· Drill 1.2 and 5 mm

 

· Adhesive tape

 

· 10 min epoxy glue

 

· CA glue

 

· PVA glue

 

· Set of wrenches

KIT CHECK

Before starting to build, use the Kit Contents list to take an 
inventory of this kit to make sure it is complete and inspect the 
parts to make sure they are of acceptable quality. If any parts 
are missing or are not of acceptable quality, or if you need assis-
tance with assembly, contact Revell Product Support.

Service-Abteilung Revell GmbH  

Henschelstr. 20-30, 32257 Bünde, Germany  

Tel: 01805 110111 (nur für Deutschland) (Anrufkosten:  

14 Cent/Min. a. d. dt. Festnetz; Mobilfunk max. 42 Cent/Min.) 

Email: Hobbico-Service@Revell.de

SPARE PARTS FOR THE MIDI EDGE 540

Support, but can be purchased from hobby shops or mail 
order/Internet order firms. Hardware items (screws, nuts, 
bolts) are also available from these outlets. If you need assis-
tance locating a dealer to purchase parts, contact Product 
Support.

Service-Abteilung Revell GmbH  

Henschelstr. 20-30, 32257 Bünde, Germany  

Tel: 01805 110111 (nur für Deutschland)  

(Anrufkosten: 14 Cent/Min. a. d. dt. Festnetz;  

Mobilfunk max. 42 Cent/Min.) 

 Email: Hobbico-Service@Revell.de

Order n°

Part name

FLWA4011

Edge 540-XXS wing set V2

FLWA4021

Edge 540-XXS fuselage set V2

FLWA4031

Edge 540-XXS landing gears aluminium bow

FLWA4041

Edge 540-XXS motor cowl V2 painted

FLWA4051

Edge 540-XXS spinner

FLWA4061

Edge 540-XXS canopy painted

FLWA4071

Edge 540-XXS elevator complete

FLWA4081

Edge 540-XXS winglets

FLWA4091

Edge 540-XXS rudder

FLWA4901

Edge 540-XXS wheel pants

FLWA4902

Edge 540-XXS CFK wing joiner

FLWA4903

Edge 540-XXS accessory set

ENGLISH

Summary of Contents for Midi EDGE 540 FLWA4001

















Reviews: