background image

Entire Contents © 2013 Hobbico

®

, Inc.

FLZA3320 RTF   FLZA3322 Tx-R

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

WARRANTY

Hobbico

 guarantees this kit to be free from defects in both 

material and workmanship at the date of purchase. This warranty 
does not cover any component parts damaged by use or 
modification. 

In no case shall Hobbico’s liability exceed the 

original cost of the purchased kit.

 Further, Hobbico reserves 

the right to change or modify this warranty without notice.

In that Hobbico has no control over the final assembly or material 
used for final assembly, no liability shall be assumed nor 
accepted for any damage resulting from the use by the user of 
the final user-assembled product. By the act of using the 
user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated 
with the use of this product, the buyer is advised to return 

this kit immediately in new and unused condition to the 
place of purchase.

To make a warranty claim send the defective part or item to 
Hobby Services at the address below:

Hobby Services

3002 N. Apollo Dr.  Suite 1

Champaign IL  61822  USA

Include a letter stating your name, return shipping address, as 
much contact information as possible (daytime telephone 
number, fax number, e-mail address), a detailed description of 
the problem and a photocopy of the purchase receipt. Upon 
receipt of the package the problem will be evaluated as quickly 
as possible.

Champaign, Illinois     (217) 398-8970

E-mail:

 airsupport@hobbico.com

SPECIFICATIONS

Wingspan:

high wing - 34 in  [865 mm]
low wing - 31 in  [785 mm]

Wing Area:

high - 195 in

2

  [12.6 dm

2

]

low - 169 in

2

  [10.9 dm

2

]

Wing Loading:

15.1−18.1 oz/sq ft  [46−48 g/dm

2

]

Length:

32.5 in  [825 mm]

Weight:

20.4−21.2 oz  [580−660 g]

Battery:

3S - 11.1V
1300mAh LiPo

Radio:

4 channel

INSTRUCTION MANUAL

Summary of Contents for Mini Switch

























Reviews: