background image

Ventura has gained enough speed to level out and re-enter
straight-and-level flight as you apply full power.

Loop:

Loops  should  always  be  done  into  the  wind.  A

proper  loop  should  be  done  on-center,  in  front  of  the
pilot. Fly straight-and-level under full power. Gradually
pull  up  elevator,  allowing  the  model  to  perform  the
loop. After the model passes through the top of the loop
reduce power. As the model completes the loop apply
full power and relax the elevator to return the model to
straight-and-level flight.

Minor damage to the wing and tail parts can be repaired
with  epoxy.  Use  tape  to  hold  the  parts  together  while
the epoxy hardens. 

Do  not  attempt  to  repair  a  damaged  propeller. 

Minor

chips  or  scratches  to  the  tips  of  the  propeller  are
acceptable,  but  performance  may  be  reduced.  If  the
propeller ever suffers major damage such as cracks near
the base of the blade, the propeller must be replaced. To
replace the propeller use a small Phillips screwdriver to
remove the spinner, then loosen the screws in the hub.
Replace the propeller and hub, tighten the screws, then
replace the spinner. Be certain the spinner and propeller
hub can spin freely and are not contacting the fuselage. 

Replacement  parts  for  the  Hobbico  Mini  Ventura  are
available  using  the  order  numbers  in  the  “

Replacement

Parts  List”

that  follows.  The  fastest,  most  economical

service  can  be  provided  by  your  hobby  dealer  or  mail-
order company. Parts may also be ordered directly from
Hobby  Services,  but  full  retail  prices  and  shipping  and
handling charges will apply. Illinois and Nevada residents
will also be charged sales tax.

To locate a hobby dealer, visit the Hobbico web site at

www.hobbico.com

.  Choose  “Where  to  Buy”  at  the

bottom of the menu on the left side of the page. Follow
the instructions provided on the page to locate a U.S.,
Canadian or International dealer. If a hobby shop is not
available, replacement parts may also be ordered from
Tower  Hobbies  at 

www.towerhobbies.com

,  or  by

calling toll free: (800) 637-6050.

Parts may also be ordered directly from Hobby Services
by  calling  (217)  398-0007,  or  via  facsimile  at  (217)
398-7721,  but  full  retail  prices  and  shipping  and
handling  charges  will  apply.  Illinois  and  Nevada
residents will also be charged sales tax. If ordering via

ORDERING REPLACEMENT PARTS

REPAIRS

13

Summary of Contents for Mini Ventura

















Reviews: