background image

Replacement parts for the Hobbico NexSTAR Select are
available using the order numbers in the Replacement Parts List
that follows. The fastest, most economical service can be
provided by your hobby dealer or mail-order company.

To locate a hobby dealer, visit the Hobbico web site at
www.hobbico.com. Choose "Where to Buy" at the bottom of the
menu on the left side of the page. Follow the instructions
provided on the page to locate a U.S., Canadian or International
dealer. If a hobby shop is not available, replacement parts may
also be ordered from Tower Hobbies at www.towerhobbies.com,
or by calling toll free (800) 637-6050, or from Hobby Services by
calling (217) 398-0007, or via facsimile at (217) 398-7721. If
ordering via fax, include a Visa or MasterCard number and
expiration date for payment.

Parts may also be ordered directly from Hobby Services, but full
retail prices and shipping and handling charges will apply. Illinois
and Nevada residents will be charged sales tax.
Mail parts orders and payments by personal check to:

Hobby Services

3002 N Apollo Drive, Suite 1

Champaign IL  61822

Be certain to specify the order number exactly as listed in
the Replacement Parts List. Payment by credit card or
personal check only; no C.O.D.

If additional assistance is required for any reason contact
Product Support by e-mail at:

productsupport@hobbico.com

or by telephone at

(217) 398-8970.

Replacement Parts

Stock Number

Description

HCAA3736.............Wing set
HCAA3737.............SpinControl Extensions/Speed Brakes
HCAA3738.............Fuselage Set w/o engine mount
HCAA3739.............Engine Mount
HCAA3740.............IsoSmooth Engine Mount
HCAA3741.............Tail Set
HCAA3742.............Landing Gear
HCAA3743.............Decal Set
HCAA3744.............NexSTAR Nylon 11x5 Prop
FUTL0995..............Futaba AFS 4-Channel Receiver

72 MHz Low

FUTL0996..............Futaba AFS 4-Channel Receiver

72 MHz High

Missing pieces..............................Contact Product Support
Instruction manual........................Contact Product Support
Plans.............................………….Not available

We are so confident that the Hobbico

®

NexSTAR

is the best

almost-ready-to-fly trainer available that we make this
guarantee: You will successfully learn how to fly with the
Hobbico NexSTAR or we will replace it with your choice of
any Hobbico  trainer of up to equal value. All we ask is that
you learn to fly under the supervision of a qualified, club-
designated instructor, follow normal safety precautions, fly
at an AMA-chartered club and construct the kit as outlined
in the included instruction manual.

If for some reason, you find the design and/or workmanship of
the NexSTAR is not conducive to learning to fly under the
conditions outlined above, contact Hobby Services, Monday
through Friday, 9AM to 5PM, to initiate the NexSTAR
replacement process. You must verify that all terms and
conditions of the flight guarantee have been met and provide
signatures from you and your AMA-club qualified instructor.

TERMS FOR U.S. AND CANADA GUARANTEE ONLY

Must fly at an AMA Chartered field

Must fly with a qualified AMA- club instructor

Must be within 60 days of purchase date

Must provide a statement about the crash and signature
from the pilot and instructor

This guarantee is effective for 60 days from the purchase
date of the kit and does not cover incidental items (engine,
radio equipment and hardware, etc.). The kit, along with the
replacement verification form and original purchase receipt
must be returned to Hobby Services for inspection no later
than 60 days after purchase. Hobbico reserves the right to
verify all information provided. The NexSTAR Success
Guarantee is only good for kits purchased and flown in the
United States and Canada. Replacement trainer kit options
are limited to flat-bottom wing trainer models available from
Hobbico and only one replacement kit per customer.

Contact Hobby Services at:

Hobby Services

3002 N. Apollo Drive, Suite 1

Champaign, IL 61822 U.S.A.

(217) 398-0007

www.hobbyservices.com

NEXSTAR SUCCESS GUARANTEE

ORDERING REPLACEMENT PARTS

27

This model belongs to:

Name

Address

City

,

State Zip

Phone n

u

mber

AMA n

u

mber

Fill in an

identification tag

and place it in

your model.

Summary of Contents for Nexstar select





























Reviews: