background image

Warranty

AquaCraft

will warrant this kit for 90 days after the purchase from defects in materials or workmanship. AquaCraft will

either repair or replace, at no charge, the incorrectly made part.

Make sure you save the receipt or invoice you were given when you bought your model! It is your proof of purchase

and we must see it before we can honor the warranty.

To return your Nitro Hammer

for repairs covered under warranty you should send your boat to:

Hobby Services 

1610 Interstate Drive

Champaign, Illinois 61822

Attn: Service Department

Phone: (217) 398-0007 9:00 am - 5:00 pm Central Time M-F

E-mail: 

hobbyservices@hobbico.com

HCAZ3012 for HCAB26**

Entire Contents © Copyright 2002

ASSEMBLY AND OPERATION MANUAL

Before Building:

We want the assembly and operation of this boat to be a success so BEFORE removing any parts from the parts bags please
read this manual thoroughly and watch the included video to familiarize yourself with the model. If for any reason you
think this model is not for you, return it to your local dealer immediately. PLEASE NOTE: Your hobby dealer cannot accept
a return on any model after assembly has begun.

Summary of Contents for Nitro Hammer









Reviews: