HobbyPCB RS-HFIQ Enclosure Kit Assembly Manual Download | Manualshive

Page: 6 / 8

background image

6.

Connect Power Switch Cable

The RS-HFIQ PCB has a jumper installed on the power switch header when the board was powered

during factory tests. Remove the jumper.

If the header on the PCB is similar to the one pictured above it may be necessary to trim the alignment

tabs off the connector.

Connect the power switch cable to the 2-pin header on the RS-HFIQ PCB

Then slide on the enclosure cover.

«
...
4
5
6
7
8
»

Summary of Contents for RS-HFIQ Enclosure Kit









Reviews:

No comments

Related manuals for RS-HFIQ Enclosure Kit

Brand: Alumax Pages: 9

CompactPCI MIC-3041

Brand: Advantech Pages: 2

Brand: Abtech Pages: 2

Brand: Pulsar Pages: 9

364215376135191

Brand: MonsterLabo Pages: 38

Brand: Thermaltake Pages: 12

Brand: Tecknet Pages: 20

Brand: Aukey Pages: 18

Brand: YORKVILLE Pages: 2

Brand: YORKVILLE Pages: 8

Brand: YORKVILLE Pages: 12

Brand: YORKVILLE Pages: 12

Brand: YORKVILLE Pages: 16

Parasource PS10P

Brand: YORKVILLE Pages: 16

Brand: YORKVILLE Pages: 18

Brand: YORKVILLE Pages: 22

SOHORAID GR4670-TB3

Brand: Raidon Pages: 32

Brand: ZALMAN Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands