4
5
ESC OVERVIEW
[13]
[12]
[11]
[14]
[15]
[16]
[6]
[7]
[8]
[10]
[19] [20]
[17] [18]
[3]
[4]
[5]
[2]
[1]
[21]
[9]
[22]
[23]
[24]
[1]
CH1
[2]
CH3
[3]
CH4
[4]
Headlight interface
[5]
Right turn signal light interface
[6]
Fog light interface
[7]
Fog light interface
[8]
Left turn signal light interface
[9]
LED
[10]
Headlight interface
[11]
Antenna
[12]
Power switch
[13]
Battery line anode
[14]
Battery line cathode
[15]
Motor interface «M+»
[16]
Motor interface «M-»
[17]
Left turn signal light interface
[18]
Right turn signal light interface
[19]
Tail light interface
[20]
Stop light interface
[21]
Backup light interface
[22]
Channel signal end
[23]
Power anode
[24]
Power cathode
SPECIFICATIONS
Product Name
: FS-R4A3-BS
Adaptive Transmitters
: FS-MG43-BS
Adaptive Models
: 1:18 simulation cars, climbing cars
Number of channels
: 4
Number of Lights
: 7
RF
: 2.4GHz ISM
2.4G Protocol
: 2A-BS
Antenna
: Single antenna
Input Power
: NiMH (5~7Cell)/ 2S Lithium batteries
Continuous/Peak Current
: 10A/50A
Data Output
: PWM
Temperature Range
: -10° ~ +60°
Humidity Limit
: 20%~95%
WaterProof
: PPX4
Distance
: >150m(Ground distance without inference)
Online Update
: NO
Dimensions
: 33mm*30mm*12mm (Excluding capacitor)
Weight
: 11g
BEC Output
: 6V/1A
Certification
: CE, FCC ID: N4ZR4A31
BINDING
The receiver automatically enters the binding state once it is powered on. Follow the steps below to bind with the transmitter.
1. Power on the transmitter while pressing the BIND button, then the transmitter enters the binding mode.
At the time, The G.LED on the transmitter flashes quickly, then release the BIND button.
2. After the receiver is powered on, it will automatically enter the binding mode if it is not connected to the transmitter in 1
second;
3. After the binding is finished, the LED of the receiver is solid on.
Notes:
Put the transmitter into binding mode first, and then put the receiver into its binding mode. If the binding is not finished
within 10s, the LED of the receiver will enter its slow flashing state.
CAR LIGHT CONTROL
The car light control is mainly to implement the changeover of lighting states and lighting modes by the setting of the
transmitter.
This receiver is preset with five modes for controlling model car lights. In each mode, the on/off states of backup lights are
consistent; in other words, the backup light is in a high-light state when the model car backs up; otherwise, it is in off state.
The turn signal light, headlight, stop light, tail light and fog light have different on/off states as follows:
• Default mode : In this mode, the turn signal light is in off state regardless of whether the model car makes a turn or not;
When braking, the stop light is in a high-light state, and otherwise, it is in off state;
The headlight, tail light and fog light are in off state.
• Mode A : In this mode, the turn signal light is in a slow flashing state when the model car makes a turn; When braking, the
stop light is in a high-light state, and when not braking, it is in a low-light state; The headlight is in a low-light state; The tail
light and fog light are in off state.
E
NGLIS
H
F
RA
N
Ç
AI
S
Summary of Contents for 1.CRX18-BL
Page 19: ...NOTES ...
