background image

EN

19

T-28 Trojan S 

Limited Warranty

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that 
the product purchased (the “Product”) will be free from defects in 
materials and workmanship at the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic dam-
age, (ii) damage due to acts of God, accident, misuse, abuse, negli-
gence, commercial use, or due to improper use, installation, operation 
or maintenance, (iii) modification of or to any part of the Product, (iv) 
attempted service by anyone other than a Horizon Hobby authorized 
service center, (v) Product not purchased from an authorized Horizon 
dealer, (vi) Product not compliant with applicable technical regulations, 
or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES 
NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY 
DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, 
WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-
INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE 
HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE 
REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

 

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy 
shall be that Horizon will, at its option, either (i) service, or (ii) replace, 
any Product determined by Horizon to be defective. Horizon reserves 
the right to inspect any and all Product(s) involved in a warranty 
claim. Service or replacement decisions are at the sole discretion of 
Horizon. Proof of purchase is required for all warranty claims. SERVICE 
OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE 
PURCHASER’S SOLE AND EXCLUSIVE REMEDY. 

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, 
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR 
PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF 
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, 
NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, 
EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH 
DAMAGES. Further, in no event shall the liability of Horizon exceed the 
individual price of the Product on which liability is asserted. As Horizon 
has no control over use, setup, final assembly, modification or misuse, 
no liability shall be assumed nor accepted for any resulting damage 
or injury. By the act of use, setup or assembly, the user accepts all 
resulting liability. If you as the purchaser or user are not prepared to 
accept the liability associated with the use of the Product, purchaser is 
advised to return the Product immediately in new and unused condi-
tion to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conflict of 
law principals). This warranty gives you specific legal rights, and you 
may also have other rights which vary from state to state. Horizon 
reserves the right to change or modify this warranty at any time 
without notice.

WARRANTY SERVICES
Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide war-
ranty support or service. Once assembly, setup or use of the Product 
has been started, you must contact your local distributor or Horizon 
directly. This will enable Horizon to better answer your questions and 
service you in the event that you may need any assistance. For ques-
tions or assistance, please visit our website at www.horizonhobby.
com, submit a Product Support Inquiry, or call the toll free telephone 
number referenced in the Warranty and Service Contact Information 
section to speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in 
the country you live and use the Product in, please use the Horizon 
Online Service Request submission process found on our website or 

call Horizon to obtain a Return Merchandise Authorization (RMA) num-
ber. Pack the Product securely using a shipping carton. Please note 
that original boxes may be included, but are not designed to withstand 
the rigors of shipping without additional protection. Ship via a carrier 
that provides tracking and insurance for lost or damaged parcels, 
as Horizon is not responsible for merchandise until it arrives and is 
accepted at our facility. An Online Service Request is available at http://
www.horizonhobby.com/content/service-center_render-service-center. 
If you do not have internet access, please contact Horizon Product 
Support to obtain a RMA number along with instructions for submitting 
your product for service. When calling Horizon, you will be asked to 
provide your complete name, street address, email address and phone 
number where you can be reached during business hours. When 
sending product into Horizon, please include your RMA number, a list 
of the included items, and a brief summary of the problem. A copy of 
your original sales receipt must be included for warranty consideration. 
Be sure your name, address, and RMA number are clearly written on 
the outside of the shipping carton. 

NOTICE: Do not ship LiPo batteries to Horizon. If you have 
any issue with a LiPo battery, please contact the appropriate 
Horizon Product Support office.
Warranty Requirements 
For Warranty consideration, you must include your original 
sales receipt verifying the proof-of-purchase date.

 

Provided 

warranty conditions have been met, your Product will be serviced or 
replaced free of charge. Service or replacement decisions are at the 
sole discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be com-
pleted and payment will be required without notification or estimate of 
the expense unless the expense exceeds 50% of the retail purchase 
cost. By submitting the item for service you are agreeing to payment 
of the service without notification. Service estimates are available 
upon request. You must include this request with your item submitted 
for service. Non-warranty service estimates will be billed a minimum 
of ½ hour of labor. In addition you will be billed for return freight. 
Horizon accepts money orders and cashier’s checks, as well as Visa, 
MasterCard, American Express, and Discover cards. By submitting 
any item to Horizon for service, you are agreeing to Horizon’s Terms 
and Conditions found on our website http://www.horizonhobby.com/
content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant 
in the country of use and ownership. If received, a non-com-
pliant Product will not be serviced. Further, the sender will be 
responsible for arranging return shipment of the un-serviced 
Product, through a carrier of the sender’s choice and at the 
sender’s expense. Horizon will hold non-compliant Product 
for a period of 60 days from notification, after which it will be 
discarded.

 10/15

Summary of Contents for UM T-28 Trojan S
























Reviews: