IT
37
1
2
4
5
6
7
7
8
8
1
3
9
350
min.400
350
min.400
03
Prova di funzionamento
Dopo i passaggi di montaggio descritti al punto 02 è possibile eseguire un’attivazione di prova. Si raccomanda
di eseguire la pulizia della vasca, di riempire la vasca da bagno con acqua ad una temperatura di 40 °C (+/- 5 ºC)
e di lasciare funzionare il sistema per 10 minuti, controllando nel frattempo il numero di giri massimo e minimo.
Attivare quindi il sistema di idromassaggio e, dopo 10 minuti, veri
fi
care la tenuta dei condotti a tubo e dei collegamenti.
Alla successiva attivazione di prova, eseguire la disinfezione ai sensi del punto 14.
L'acqua va fatta de
fl
uire completamente dopo il montaggio della vasca e dopo il controllo di tenuta, al più tardi 24 ore
dopo il riempimento della vasca. Pulire quindi la vasca. Durante il montaggio proteggere la vasca da eventuali danni. In
caso contrario la garanzia decade.
04
Chiusura della vasca
Dopo l’attivazione di prova, montare il rivestimento in vetro o installare la vasca da bagno veri
fi
cando quanto segue:
1.
Tutti i sistemi di tubature preistallati nella vasca e posizionati dal produttore, nonchè i componenti del sistema
devono essere collocati fuori la muratura.
2.
I componenti del sistema esposti, ed in particolare il lato di ventilazione presso il motore della pompa, devono
essere coperti per non essere sporcati.
3.
Disporre la chiusura cosi che i componenti del sistema non siano toccati e bagnati dall'acqua. E' vietato l’utilizzo
della vasca senza la copertura tranne durante prova di funzionamento.
4.
Tra il bordo della vasca ed il rivestimento in vetro dovrebbe essere mantenuta una fessura di 3-4 mm
per la guarnizione in silicone (si raccomanda di rispettare le avvertenze del produttore relativamente al campo
di applicazione!).
5.
Per tutti i modelli occorre posizionare delle aperture di revisione accessibili e apribili facilmente
di larghezza minima da 400 a 450 mm e altezza di 350 mm, conformemente a tutti i disegni e dimensioni
allegati.
Inoltre, occorre provvedere ad un foro d'ispezione nella zona di scarico.
L’elemento d'ispezione può essere aperto solo con gli strumenti adeguati. Necessariamente devono essere
mantenute le dimensioni indicate, poichè in caso di una necessaria manutenzione solo allora è possibile
un facile smontaggio dei componenti del sistema. La soluzione ideale sarebbe l’installazione di una griglia
di ventilazioneispezione Hoesch di dimensioni 420 x 325 mm (numero articolo 6683).
6.
A causa delle bocchette rotanti dell’idromassaggio e della sof
fi
ante, occorre provvedere ad un libero
fl
usso
d’aria (ca. Vo = 60,0 m³/h con mass. quantità giri di sof
fi
ante), perchè altrimenti, quando la copertura sarà
chiusa ermeticamente, mancherà il
fl
usso d’aria alle bocchette rotanti whirl e alla sof
fi
ante. E’ suf
fi
ciente un foro
nella copertura della dimensione 100 x 100 mm. L’applicazione della griglia di ventilazione-ispezione garantirà il
necessario
fl
usso dell’aria.
05 Schema
1 Connessione di rete del comando:
presa di collegamento da predisporre localmente,
230 V~, 50/60 Hz, 10 A
2 Telecomando
3 Pompa
4 Comando
5 Unità sof
fi
ante
6 Comando
7 Fari LED subacquei
8 Apertura di revisione
9 Tastiera
Summary of Contents for ERGO+ Series
