6
Adres producenta/ Adresse des Herstellers/ Manufacturer’s Address/ Адрес производителя
GTV Poland Sp. z o.o. Sp. k., ul. Przejazdowa 21, 05-800 Pruszków
the manufacturer or service, the gas container must be dismantled and then the burner must be properly packed.
Service address: GTV Sp. z o.o. Sp. K., ul. Przejazdowa 21, 05-800 Pruszków, Poland.
Work with the burner in clean places, away from flammable or greasy materials and use eye and hand protection. When the burner is
not to be used for a long time or for transport, the gas container must be removed.
OPERATION
Gas tank refill
Refill the gas outdoors or in well-ventilated areas. Keep a distance from fire or heat sources and bystanders. First close the gas valve
by turning the gas control knob in the direction marked „-” and trigger lock button is at “OFF” position. Make sure that the burner
connection seal and valve is not damaged or worn. If any signs of wear or damage to these components are observed, the refill of a gas
is prohibited. Gas container has to be equipped with adequate adapter which fits to burner gas inlet valve. Please keep burner bottom
up (gas inlet valve is located at bottom of gas tank). Than position gas container outlet with adequate adapter nearby burner gas tank
inlet valve. Fit each other and press down gas container. Please keep them both axial and avoid side moving as it can cause gas leaking
while refill. After gas starts to leak from the connection between gas container adapter and burner’s inlet valve it means gas tank is full
and refill should be stopped. Turn around burner and put it on stable surface for few minutes till the gas pressure in tank will stabilize.
Warning! Make sure there are no gas leaks, preferably with soapy water. It is forbidden to work with a burner in which a gas leakage
was found.
Burner operation
Burner has following buttons:
• Gas adjustment knob,
• Trigger with valve and piezo,
• Trigger lock,
• Constant working lock.
Make sure there are no gas leaks before starting operation. In order to start the burner, turn the adjustment knob in the direction mar-
ked with „+”. Than press trigger lock bottom which protects against unexpected pressing of trigger. It is located at side of burners body
at same level as trigger. Then set the gas on by pressing the trigger and keep it pressed. Burner will be heated up. Adjust the flame
using the adjustment knob. Trigger lock bottom could be released as it will stay pressed as long as trigger is pressed. After lighting the
gas, it is advisable to wait about one minute until the burner heats up, which should be in a vertical position. The flame of gas should
be observed during this time. In the initial phase there may be a slight phenomenon of flickering. If it does not go out spontaneously,
extinguish the flame and contact the manufacturer. If the flame colour changes from blue to orange, the burner must also be returned
to an authorised service centre.
After release trigger button burner will be automatically stopped. For continuous working mode please push-up continuous working
mode bottom which is located just below trigger. Than burner will work continuously even if trigger is not pressed-in. Another press-in
trigger button will release triggers lock. After burner heats up it is allowed to work at any angle.
Warning! Do not put down or heat the burner when it is lit.
Burner extinguishing
To extinguish the burner, release trigger button. Built-in valve will automatically stop gas flow and flame will go out spontaneously.
Turn the adjustment knob in the direction marked „-” until the resistance occurs. Let the burner to cool down completely.
Warning! It is forbidden to immerse or pour water over the burner for cooling purposes.
Disconnect gas container
The gas container can be disconnected at any time, even when it has not been fully used up. To do so, turn the adjustment knob in the
direction marked „-” until it stops. Wait until all burner components have completely cooled down. Turn the gas container as far as it
will go counter-clockwise and then remove it from the burner.
Maintenance
Clean the device with a damp cloth. Larger dirt should be cleaned with soapy water. Do not use abrasive cleaners. In case of any mal-
functions or contamination of the nozzle, stop using the burner and contact the manufacturer’s service point. It is forbidden to modify
the burner and to clean the nozzle by yourself, especially with sharp objects.
Storage
Store the device in an upright position in a dry and well-ventilated place, inaccessible to unauthorised persons, especially children.
