ENGLISH
- 4
2.1 UNPACKING
(Figs. 1-2-3-4)
- Upon the machine delivery, remove the
external packing and then cut the holders
(1) (Fig.1). Raise the handle (2) by pulling
the unlocking handle (3) (Fig.2);
- Lift the wheels (4) by leveraging the han-
dle (2), rotate the machine and lay the
wheels on the ground (Fig. 3);
- Lift the machine body (5) by leveraging
the handle (2) and move the machine
(Fig. 4).
2.2 COMPONENT
ASSEMBLY
2.2.a - Pad assembly (Figs. 5/7)
- Tilt the machine, pivoting, with the handle
straight, with your feet on the wheels and
place it on the handle (Fig. 6).
- Mount the pad (8) on the pad holder (9)
(Fig. 6).
- Make sure the outer perimeter of the pad
(8) corresponds with the outer perimeter
of the pad holder (9) and then lock it on
the pad holder’s teeth pressing down with
your fingers (Fig. 7).
WARNING:
Use only pads supplied by the manufac-
turer for the specific machine model.
Using other types of pads can compro-
mise the safety of the machine.
2.2.b - Assembling the tank
(optional) (Figs. 8-14)
- Loosen he knob (10) on the upper sup-
port (11) of the handle (Fig. 8).
-
Make sure that the lower support (12)
rests on the base of the handle joint (Fig.
11).
- Screw the chain (13) onto the top of the
tank (14) (Fig. 9).
- Connect the tube (15) into the fitting (16)
at the bottom of the tank (14) (Fig. 10).
- Place the tank (14) on the lower support
(12), by aligning the tank slots (17) with
the specific support guides (18) (Fig. 11).
- Press the tank (14) so that the slots are
against the end stops on the lower sup-
port (12) guides.
- Lower the upper support (11) and attach
its coupling to the coupling tab (19) on top
of the tank (14) (Fig. 12).
- Tighten the knob (10) on the upper sup-
port (11) of the handle (Fig. 12).
- Connect the tube (20) fitting (15) to the
hole on the machine body (Fig. 13).
- Attach the chain (13) to the hook of the
water supply lever (30) (Fig. 14).
2.2.c - Brush assembly (optional)
(Fig. 15)
- Unscrew the four wing knobs (22) and re-
move the pad driver (23).
- Tighten the desired brush (24) in place of
the driver with the wing knobs (22).
Make sure to firmly tighten the wing
knobs using pliers.
2.2.d - Electrical spray accessory
assembly (Optional)
CAUTION:
The optional equipment may exclusively
be assembled by a specialized technician
following the assembly instructions that
accompany the accessory.
Manuale HU30-933_HOLLU_OM143_3l_1ed_07-2019.indd 4
16/07/2019 08:37:50
Summary of Contents for OM 143
