manualshive.com logo in svg

Holtek HT45F4050, Manual

The Holtek HT45F4050 user manual is available for free download on 88.208.23.73:8080. This comprehensive manual provides step-by-step instructions on operating and configuring the HT45F4050 microcontroller, ensuring users can fully utilize its features. Enhance your product experience by accessing the free manual today.

Share
Download
background image

Rev. 1.00

200

September 11, 2018

Rev. 1.00

201

September 11, 2018

HT45F4050

A/D NFC Flash MCU

HT45F4050

A/D NFC Flash MCU

NFC Interrupt

The NFC Interrupt is controlled by several NFC communication conditions. These conditions are 
MCU reading/writing NFC memory completed, RF reading/writing NFC memory completed, MCU 
reading/writing NFC memory when RF reading/writing NFC memory is in progress, field condition 
detected, NFC memory accessed by MCU or RF error occurance, which are detailly defined in the 
NFC_INTF register. When one of these conditions occurs, an interrupt pulse will be generated to 
get the attention of the microcontroller. To allow the program to branch to its respective interrupt 
vector address, the global interrupt enable bit, EMI, the

 

NFC Interrupt enable bit, NFCE, and the 

interrupt enable bit of any conditions described above, must first be set. When the interrupt is 
enabled, the stack is not full and the corresponding condition occurs, a subroutine call to the NFC

 

Interrupt vector, will take place. When the interrupt is serviced, the NFC Interrupt flag, NFCF, will 
be automatically cleared. The EMI bit will also be automatically cleared to disable other interrupts.

 

However, the NFC_INTF register flags must be manually reset by the application program.

EEPROM Write Interrupt

The EEPROM Write Interrupt is contained within the Multi-function Interrupt. An EEPROM 
Write Interrupt request will take place when the EEPROM Write Interrupt request flag, DEF, is set, 
which occurs when an EEPROM Write cycle ends. To allow the program to branch to its respective 
interrupt vector address, the global interrupt enable bit, EMI, EEPROM Write Interrupt enable bit, 
DEE, and associated Multi-function interrupt enable bit must first be set. When the interrupt is 
enabled, the stack is not full and an EEPROM Write cycle ends, a subroutine call to the respective 
Multi-function Interrupt vector will take place. When the EEPROM Write Interrupt is serviced, the 
EMI bit will be automatically cleared to disable other interrupts. However, only the Multi-function 
interrupt request flag will be automatically cleared. As the DEF flag will not be automatically 
cleared, it has to be cleared by the application program.

LVD Interrupt

The Low Voltage Detector Interrupt is contained within the Multi-function Interrupt. A LVD 
Interrupt request will take place when the LVD Interrupt request flag, LVF, is set, which occurs 
when the Low Voltage Detector function detects a low power supply voltage. To allow the program 
to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, Low Voltage 
Interrupt enable bit, LVE, and associated Multi-function interrupt enable bit, must first be set. When 
the interrupt is enabled, the stack is not full and a low voltage condition occurs, a subroutine call to 
the Multi-function Interrupt vector, will take place. When the Low Voltage Interrupt is serviced, the 
EMI bit will be automatically cleared to disable other interrupts, however only the Multi-function 
interrupt request flag will be also automatically cleared. As the LVF flag will not be automatically 
cleared, it has to be cleared by the application program. 

TM Interrupts 

The Compact, Standard and Periodic TMs have two interrupts, one comes from the comparator A 
match situation and the other comes from the comparator P match situation. All of the TM interrupts 
are contained within the Multi-function Interrupts. For all of the TM types there are two interrupt 
request flags and two enable control bits. A TM interrupt request will take place when any of the 
TM request flags are set, a situation which occurs when a TM comparator P or A match situation 
happens.

Summary of Contents for HT45F4050










































































































































































































































Reviews:

No comments

Related manuals for HT45F4050

Western Digital WDBAAE3200ASL - My Passport Studio Specifications preview
WDBAAE3200ASL - My Passport Studio
Brand: Western Digital Pages: 2
IBM StorVize V7000 Gen2 Quick Installation Manual preview
StorVize V7000 Gen2
Brand: IBM Pages: 188
Chieftec CEB-2355S User Manual preview
CEB-2355S
Brand: Chieftec Pages: 18
IBM 9835-415 Deployment Manual preview
9835-415
Brand: IBM Pages: 126
Far Tools WB 100SB Original Manual Translation preview
WB 100SB
Brand: Far Tools Pages: 10
Synology DiskStation Series Upgrade Installation Instructions preview
DiskStation Series
Brand: Synology Pages: 6
Oracle StorageTek SL8500 Safety And Compliance Manual preview
StorageTek SL8500
Brand: Oracle Pages: 59
Fujitsu PG-HDH61A User Manual preview
PG-HDH61A
Brand: Fujitsu Pages: 12
Fujitsu PG-HD6G1C User Manual preview
PG-HD6G1C
Brand: Fujitsu Pages: 16
Fujitsu MPG3xxxAT Product Manual preview
MPG3xxxAT
Brand: Fujitsu Pages: 201
Fujitsu PG-HD2E4H User Manual preview
PG-HD2E4H
Brand: Fujitsu Pages: 14
Fujitsu MPC3045AH Product Manual preview
MPC3045AH
Brand: Fujitsu Pages: 185
Fujitsu MPC3032AT Product Manual preview
MPC3032AT
Brand: Fujitsu Pages: 179
Fujitsu MPA3017AT Product Manual preview
MPA3017AT
Brand: Fujitsu Pages: 176
Fujitsu MPD3091AH Product Manual preview
MPD3091AH
Brand: Fujitsu Pages: 191
Fujitsu MJA2080BH Product/Maintenance Manual preview
MJA2080BH
Brand: Fujitsu Pages: 320
Fujitsu MPD3043AT Product Manual preview
MPD3043AT
Brand: Fujitsu Pages: 191
Fujitsu MPB3021AT Product Manual preview
MPB3021AT
Brand: Fujitsu Pages: 180

Brands by name

Popular brands

Load more brands