HOLZMANN MASCHINEN GMBH WWW.HOLZMANN-MASCHINEN.AT
39
BS 712TURN; BS712TURN-G
18
STORAGE
NOTICE
Improper storage can damage and destroy important components. Only store packed
or unpacked parts under the intended environmental conditions
!
When not in use, store the machine in a dry, frost-proof and lockable place to prevent the
formation of rust on the one hand and to ensure that unauthorised persons and in particular
children have no access to the machine on the other.
19
DISPOSAL
Observe the national waste disposal regulations. Never dispose of the machine,
machine components or equipment in residual waste. If necessary, contact your
local authorities for information on the disposal options available.
If you buy a new machine or an equivalent device from your specialist dealer,
he is obliged in certain countries to dispose of your old machine properly.
20
TROUBLE SHOOTING
WARNING
Danger due to electrical voltage!
Manipulating the machine with the power supply
up may result in serious injury or death. Before carrying out any troubleshooting
work, always disconnect the machine from the power supply and secure it against
unintentional recommissioning.
Many possible sources of error can be excluded in advance if the machine is properly connected
to the mains. If you are unable to carry out necessary repairs properly and/or do not have the
required training, always consult a specialist to solve the problem.
Fault
Possible cause
Remedy
Machine does not start
▪
Machine not connected to power
supply
▪
Fuse of power circuit defect or
not suitable
▪
Cable defect
▪
Check all power connections
▪
Change fuse
▪
Change cable
Saw band does not come to
full speed, no power
▪
To long extension cord
▪
Power supply not matching with
motor requirements.
▪
Weak, instable/volatile power
supply
▪
V-belt tension too low
(BS712TURN)
▪
change to suitable extension
cord with sufficient cross-
section, insulation and length
▪
Let check by electrician
▪
Contact electric power
company
▪
Adjuste V-Belt tension
Motor gets hot very fast and
has weak performance
▪
Motor does not receive power on
one or even 2 phases
▪
Shut off machine
immediately. Let the
connection to supply circuit
be checked by an electrician!
Saw band runs in opposite
direction
▪
2 of the 3 leading phases are
switched whether in Plug or
socket
Shut off machine
immediately. Let the
connection to supply circuit
be corrected by an
electrician!
Machine vibrates
▪
Placed on uneven underground
▪
Motor or any other parts loose
▪
modify
▪
check all screw joints if
tightened
Bad cuts
▪
too high descent velocity
▪
unsuitable saw band for cutted
material
▪
worn saw band
▪
saw band not tensioned correctly
▪
saw band guide outbalanced
▪
Reduce the descent velocity
▪
Use e.g. for stainless steel HQ
Bi-Metal bands only
▪
replace
▪
tension saw band correctly
▪
readjust saw band guide
Summary of Contents for BS712TURN
