Homa Saniflux Series, Installation And Operation Instruction Manual

10 

2. Safety Warnings 

2.1. General instructions 
Signs used to mark instructions in this manual 

Safety instructions in these operating instructions, 

which, if not observed, could cause a danger for persons 
are marked with the general symbol in accordance with DIN 
4844-W 9. 

Warnings against electrical voltage are marked with the 

safety symbol in accordance with DIN 4844-W 8. 
 
2.2. General Safety Precautions 
General regulations and guidelines not mentioned in the  
safety warnings retain their validity. 

These operating instructions contain basic instructions, 

which have to be adhered to during installation, operation 
and maintenance. These operating instructions must be 
read by the installer and the operator before installation and 
use of the pump and have to be kept available on side at all 
times. Persons who are not familiar with the operating in-
structions shall not use this product. 

The unit must be installed by a technically experienced 

plumber. 

The working area has to be closed off expediently 

and must adhere to local workplace regulations. 

Always use personal safety equipment such as safety 

boots, rubber gloves, safety glasses and helmet. 

Make sure that the emergency exit from the workplace 

is not barricaded. 

If you have to work with welding tools or electric tools, 

make sure that there is no explosion hazard. 

Immediately after repair or maintenance work, all safety 

and protection equipment must be reinstalled and placed in 
function again. 

The operator of the pump is responsible for third par-

ties within the work area. 

Never put a hand or finger into inlet or discharge of the 

pump while the impeller is rotating. 

All other rules and regulations and local codes covering 

health and safety must be observed. In accordance with 
product liability law, we point out that we shall not be liable 
for damages caused by the pump due to non-observance 
of the instructions and guidelines set forth in the operating 
instructions. The same product liability are  
valid for accessories. 
 

3. Applications and Technical Description 

3.1. Applications 
HOMA disposal units Saniflux are used for pumping waste 
water and effluent from rooms which are below the sewer 
level. 
Before the pumping of chemically aggressive liquids, the 
resistance of the pump materials must be checked. 

3.2. Product description 
Odour-tight and watertight complete lifting station with one 
pump. The integrated cutter system cuts all soft solits into 
small particles, so that the liquid may be pumped through 
DN 25 discharge pipes. The lifting station consists of a col-
lecting tank with toilet connection at the front of the box, two 
DN 40 inlets with integrated non return valve for the con-
nection of inlet pipe on the sides, a adjustable discharge 
pipe DN 25 (also with integrated non return valve) and air 
vent. 
 
3.3. Technical Data 
 

Discharge 

1" (DN 25) 

Supply Voltage 

230V/ 1Ph, 50Hz 

Motorpower P

1

 0,65 

kW 

Motorpower P

2

 0,35 

kW 

Nominal current 

2,1 A 

Enclosure class (complete unit) 

IP 44 

Insulation class 

B 

Speed 2900 

rpm. 

Total head 

6,5 m  

Flow 72 

l/min. 

Cable 

1,1 m with plug 

Weight 7 

kg 

 
 
3.4. Operating Conditions 
Maximum liquid temperature: 35°C, short term up to 
60°C. 
Operation: The motors are designed for intermittent opera-
tion (S3) 3 / 7 min. (3 min. operation, 7 min. break). The 
integrated thermal switch protects the motor from overheat-
ing by cutting of the supply to the pump. 
 
3.5. Explosive Environments 

This unit is not admitted for use in explosive environ-

ments. 

4. Warranty 

Our warranty only covers pumps which are installed and 
operated in accordance with these installation and opera-
tion instructions and accepted codes of good practice and 
being used for the applications mentioned in these in- 
structions. 
 

5. Transport and Storage 

Never use the cable or the pressure hose to lift, lower 

or transport the unit. 

The unit may be transported and stored in vertical or 

horizontal position. Make sure that it cannot roll or fall over. 
For longer periods of storage, the unit should be protected 
against moisture, frost or heat. 
 

6. Electrical Connection 

6.1. General instructions 

Before operation, an expert check must secure that the 

required electrical protection measures exist. The connec-
tion to ground, earthing, isolating transformer, fault current 
breaker or fault voltages circuit must correspond to the 
guidelines set forth by the responsible power plant.