Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Insert tree bottom (D) into the tree stand and tighten the screw.
(See Fig. 1)
Step 2. Insert tree lower middle section (C) into the tree bottom (D).
(See Fig. 2)
Step 3. Insert tree upper middle section (B) into the tree lower middle
section (C). (See Fig. 3)
Step 4. Insert the tree top (A) into the tree upper middle section (B).
(See Fig. 4)
Step 5. Remove the plastic protective cover on the plug fixed on the
pole of the bottom section (D). Insert the plug into the end
connector of the power supply cord with an on/off foot pedal
switch according to the magnified drawing on Fig. 5.
Step 6. Allow branches to fall into place or gently pull branches up and out.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 6)
Step 7. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and one at the center of the main
stem. Repeat pattern for each branch. (See Fig. 7)
Step 8. Plug the well-connected power supply cord from the bottom
section (D) into electrical outlet. Please note this tree comes
with an on/off foot pedal switch for easy illumination.
Operation
Turning on the tree
NOTE: If some bulbs do not light or flicker, search for any loose, broken bulbs
and /or missing bulbs. Replace bulbs promptly with the replacement bulbs
provided in order to maintain the performance and life expectancy of your tree.
Step 1. Connect each tree section well and plug the power cord into a wall
outlet.
Maintenance
Fuse Replacement
A)
Extension cord fuse replacement (1 replaceable 5 A, 125 V fuse is located
in the plug):
Note: This plug will fit in a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug.
1. Grasp plug and remove from its power source.
2. Locate blown fuse by sliding access cover on top of plug towards prongs.
3. Remove blown fuse by turning the plug over. Fuses should fall into your
hand (gentle tapping may be required).
4. Locate spare replacement fuse included in plug.
5. Insert spare replacement fuse. Close fuse cover by sliding fuse access
cover towards the cord.
CAUTION:
To reduce risk of fire – replace fuse in extension cord
with only 5 A, 125 V fuse. Do not replace attachment plug. Discard product if
the attachment plug is damaged.
B)
Fuse replacement of the plug fixed on bottom section (D):
1.
Grasp power supply plug and remove from its power source.
2.
Locate the plug fixed on bottom section (D).
Slide access cover on top of plug towards prongs.
3.
Remove blown fuse.
4.
Locate spare replacement fuse provided with
product.
5.
Insert spare replacement fuse. Close fuse cover
by sliding fuse access cover back.
CAUTION
: To reduce risk of fire – replace
fuse in plug fixed on bottom section (D) with only 3 A, 125 V fuse. Discard
product if the attachment plug is damaged.
Replacing the bulbs
1. Grasp plug and remove from its power source.
2. Unlock the lamp lock on the socket of the bulb.
3. Pull bulb AND plastic base straight out of socket. Do not twist bulbs while
you are removing them.
4. Replace burnt out bulb with 2.5 V, 0.425 W bulb ONLY. (Additional bulbs
are included for your convenience.)
5. Relock the lamp lock on the socket of the bulb.
If the new lamp base does not fit in lampholder, follow these steps:
a) Remove the base of burned out lamp by straightening lamp leads and
gently pull lamp out.
b) Thread leads of new lamp through holes in old base
with one lead in each hole.
c) After lamp is fully inserted into ase, bend each lead up,
like other lamps in the light set so that the leads will touch
the contacts inside the lampholder.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the plug cord from the wall outlet. And remove your power
supply cord with an on/off foot pedal switch from bottom section (D)
and save it.
Step 3. Gently lift the tree top straight up to remove from the center section
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
UL Model No. TMH9-5(2.72)
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that all tree sections are plugged into each other
and that the tree is plugged into the wall outlet.
Check for blown fuses at the extension cord plug and the
plug fixed on the bottom section (D). Replace as needed
with the replacement fuses provided.
Check for loose, broken, or missing bulbs and replace as
needed with the replacement bulbs provided.
If you are still experiencing problems with the tree please
call 1-877-527-0313 for instructions.
