Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Insert tree bottom (E) into the tree stand and tighten the screws.
(See Fig. 1)
Step 2. Insert lower middle section (D) into the tree bottom (E). (See Fig. 2)
Step 3. Insert the middle section (C) into the lower middle section (D). (See
Fig. 3)
Step 4 Insert upper middle section (B) into the middle section (C). (See
Fig. 4)
Step 5. Insert tree top (A) into the upper middle section (B). (See Fig. 5)
Step 6. Insert the provided power cord into the connector on the tree
bottom (E) in right direction properly and tightly (always match the
protuberance of the end connector of power cord to the concave
of the connector found on the tree bottom (E) according to the
magnified drawing on fig. 6.).
Step 7. Allow branches to fall into place or gently pull branches up and out.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 7)
Step 8. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and one at the center of the main
stem. Repeat pattern for each branch. (See Fig. 8)
Step 9. Plug the power cord into a proper outlet. Please note this tree
comes with a foot pedal switch and remote control for timer
control.
a.
Press the foot pedal switch for less than two seconds to switch
on the tree.
b.
Press the foot pedal switch for more than two seconds to select
below timer hours:
1)
One indicator light on foot pedal switch turns on:
The tree lights will automatically run through a 2-hours ON,
22-hours OFF cycle.
2)
Two indicator lights on foot pedal switch turn on:
The tree lights will automatically run through a 4-hours ON,
20-hours OFF cycle.
3)
Three indicator lights on foot pedal
switch turn on:
The tree lights will automatically run
through a 6-hours ON, 18-hours
OFF cycle.
4)
Four indicator lights on foot pedal switch turn on:
The tree lights will automatically run through a 8-hours ON,
16-hours OFF cycle.
5)
Switch off the tree to shut down the timer function.
Instruction of remote control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
1.
Press the button ON or OFF to turn on or off the lights.
2.
Press the 2H, 4H, 6H or 8H button to select the different timer hours.
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1.
Replace with a new button cell “CR2025” (3 volt)
into the compartment.
CAUTION:
DO NOT DISPOSE OF
BATTERIES IN FIRE. BATTERIES MAY EXPLODE
OR LEAK.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Operation
Turning on the tree
Step 1. Connect each tree section well and plug the power cord into a wall
outlet.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the power cord from the wall outlet. And remove your
power cord from tree bottom (E) and save them.
Step 3. Gently lift the tree top straight up to remove from the center section
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that all tree sections are connected into each
other well by pressing each section down and rotating.
Make sure the power cord is well connected to the tree
bottom (E) and that the tree is plugged into the wall
outlet.
If you are still experiencing problems with the tree please
call 1-877-527-0313 for instructions.
Adapter Model No. LE-0309ADSP12V
CAN ICES-005(B)./NMB-005(B).
CAN RSS-Gen/CNR-Gen
