Step 4. Allow branches to fall into place or gently pull branches up and
out. When adjusting branches be sure that all wires are free of
branch hinges. (See Fig. 6)
Step 5. Shape the branches. Starting with tips closest to the pole,
shape one tip to the right, one to the left and one at the center
of the main stem. Repeat pattern for each branch. (See Fig. 7)
Step 6. Plug the power cord from the tree section (C) into a proper
outlet.
Turning on the tree
Step 1. Plug the power cord from the tree section (C) into a proper
outlet.
Replace the fuse.
a)
Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
b)
Open fuse cover. Slide open fuse access cover on top of
attachment plug towards blades.
c)
Remove fuse carefully.
d)
Risk of fire. Replace fuse only with 3 Amp,
125 Volt fuse (provided with product).
e)
Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f)
Risk of fire. Do not replace attachment plug. Contains a safety
device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
Replace the lamp.
a)
Grasp plug and remove from the receptacle or other outlet device. Do
not unplug by pulling on cord.
b)
Unlock the burned out LED bulb by lifting the hook and pulling both
the bulb and plastic base straight out of the bulb holder. Do not twist
bulbs.
c)
Replace burned out bulb with 3.0/2.0 volt, 20 mA LED type bulb
ONLY. (Replacement bulbs included)
d)
Lock the LED bulb.
CAUTION
1.
To reduce the risk of overheating, replace burned-out lamps promptly.
Use 3.0/2.0 Volt, 20 mA LED lamps only.
2.
Risk of fire. This product does not contain lamp shunts, which allow the
product to operate if one lamp burns out. Replace lamps only with the
spare lamps provided with this product.
If the new lamp base does not fit in lampholder, follow the steps below
before step c.
1.
Pull the reflector out.
2.
Remove the base of burned out lamp by straightening lamp leads
and gently pulling lamp out.
3.
Thread leads of new lamp through
hole in old base with one lead in each
hole (always match the long lead of
new lamp to the hook of lamp base.)
4.
After bulb is fully inserted, bend each lead up so that the leads will
touch the contacts inside the bulb holder.
5.
Insert the reflector into the base.
CAUTION! –
ALWAYS UNPLUG YOUR TREE FROM ITS
POWER SOURCE BEFORE ATTEMPTING FUSE AND BULB
REPLACEMENT.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the cord from the wall outlet and then disconnect each
section of the tree. Remove the power cords from the tree
bottom (C).
Step 3. Gently lift the tree top straight up to remove from the center
section and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it
shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that connectors of all tree sections are
connected into each other well. Make sure power
cord plug is securely inserted into a working
electrical outlet.
Check for blown fuses at the power cord plug. Replace
as needed with the replacement fuses provided.
Check for loose, broken, or missing bulbs and replace
as needed with the replacement bulbs provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Model No. TMP6.5-6(0.1)
Operation
Maintenance
