Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a)
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 0.37 A 120 V 60
Hz.
c) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor applications,
connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If
one is not provided, contact a qualified electrician for proper installation.
d) This seasonal use product is not intended for permanent installation or
use.
e) Do not mount or place near gas or electric heaters, fireplace, candles or
other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, or when retiring for the
night, or if left unattended.
i) This is an electric product – not a toy! To avoid risk of fire, burns
personal injury and electric shock it should not be played with or placed
where small children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light string.
l) Do not close doors or windows on the product or extension cords as this
may damage the wire insulation.
m) Do not cover the product with cloth, paper or any material not part of
the product when in use.
n) Do not move the tree by pulling the tree tips or tree branches.
o) Read and follow all instructions that are on the product or provided with
the product.
p)
SAVE THESE INSTRUCTIONS.
Package Contents
A.
Tree top
Qty: 1
B.
Tree center
Qty: 1
C.
Tree bottom
Qty: 1
D.
Stand with an eye
bolt
Qty: 1
E.
Power cord
Qty: 1
F.
Latch
Qty: 2
7.5ft Fenwick Pine Micro Dot Tree
SKU# 1006215503
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step 2. Open the stand to a 90 degree angle until the hole lines up with the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
CAUTION! – ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE
BEFORE ASSEMBLING OR
DISASSEMBLING.
Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Carefully insert bottom section (C) of tree into tree base and
tighten the screw. (See Fig. 1)
Step 2. Insert the middle section (B) of the tree into the bottom section
(C). (See Fig. 2)
Step 3. Insert the top section (A) into the middle section (B). (See Fig. 3)
Step 4. Allow branches to fall into place or gently pull branches up and out.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 4)
Step 5. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and one at the center of the main
stem. Repeat pattern for each branch. (See Fig. 5)
Step 6. Plug the well-connected power cord from the tree section (C)
into a proper outlet.
Step 7. Please note this tree comes with a foot pedal switch for easy
illumination and changing functions. This tree is Color Changing,
the 8 lighting options available are:
1.
Steady Warm White
2.
Flashing Warm White
3.
Fade In and Fade Out Warm White
4.
Steady Multicolor
5.
Flashing Multicolor
6.
Fade In and Fade Out Multicolor
7.
Sequential Multicolor & Warm White
8.
Color Changing
These functions can be changed by pressing the foot pedal
switch
Pre-Assembly
Assembly
