Christmas Tree
Model: TG76M3W89D24
Sku # 1004 044 657
Step 1.
Grasp the power adapter or power cord plug,
and than unplug from the power outlet.
Do not pull the power cord.
LAMP REPLACEMENT
Step 2. Lift up lamp lock tab, then pull the
lamp and plastic lamp base
straight out of the lamp-holder.
Step 3.
Replace with a new spare lamp
provided with this product.
(Reference figure only)
NOTE: If some bulbs do not light or flicker, search for any loose
plugs and/or broken, loose, or missing bulbs. Replace bulbs
promptly with the replacement bulbs provided in order to
maintain the performance and life expectancy of your tree.
Step 1
. Connect the light strings of the tree together and plug the
adapter into a wall outlet.
Step 2
. If the tree comes with a foot pedal, step on the On/Off
button.
Operation
Turning on the tree
This tree package includes hinge pins, washers and bulbs for any
replacement or repair that you need to perform on your tree. If
extra parts are needed, contact the Customer Service Team at
1-877-527-0313 between the hours of 8 am and 5 pm EST,
Monday through Friday.
Repairing Loose Hinges
Step 1
. Place the branch into the slot of the bracket
Step 2
. Insert a new hinge pin through the holes of the
bracket and secure with a washer.
Maintenance
Spare parts
1. Before using or reusing, inspect product carefully. Discard any
products that have cut, damaged or frayed wire insulation or
cords, cracks in the lampholders or enclosures, loose
connections, or exposed copper wire.
2. Before disassembling the tree, unplug the tree and remove all
ornaments and decorations.
3. Gently lift the tree top straight up to remove from the center
section and fold all branches towards the pole.
4. Repeat this step for the center and bottom tree sections.
5. When storing the product, carefully remove the product
from wherever it is placed, including tree, branches, or bushes,
to avoid any undue strain or stress on the
product conductors, connections, and
wires. Cover the protective cap on the
poles to avoid damaging the internal parts.
6. When not in use, store neatly in a cool,
dry location protected from sunlight.
7. Keep out of reach of pets and children.
Use and Care Instructions
CAUTION:
Use only power adapter that was provided with this product.
Using a different power adapter will damage the lights and cause
fire, electrical shock hazard.
TM
Troubleshooting
Problem Solution
The tree does not
light
Ensure that all tree sections are plugged into
each other and that the tree is plugged into
the wall. If your tree came with a foot pedal,
step on the On/Off button.
Check for loose, broken, or missing bulbs and replace
as needed with the replacement bulbs provided
Remote Control Instructions
1. Remove the insultation tab of the remote control.
2. Press either selector button and wait for a second to enjoy light
effects in the following sequence (see DUAL COLOR
LIGHT CONTROLLER & REMOTE CONTROL).
Insulation Tab
DUAL COLOR LIGHT CONTROLLER & REMOTE CONTROL
Simply press the selector button to select from the following
light functions: (1) CLEAR - MULTI: FADING
(2) CLEAR: FADING (3) CLEAR - MULTI: ALTERNATING
(4) CLEAR: STEADY (5) CLEAR - MULTI: SLOW FADING
(6) MULTI: STEADY (7) MULTI: FADING (8) COMBINATION
Light Controller
Selector
Button
Remote
Controller
Cover
Battery
CR2032
BATTERY REPLACEMENT
1. Loosen the screw of the battery cover with a screwdriver (not included).
2. Replace the used battery with a new CR2032 button cell battery
(not included). Make sure that the battery is installed with the
correct polarity (+ and -).
3. Retighten the screw to close and secure the battery cover.
WARNING
1. Dispose used battery properly. observe local regulations regarding
disposal of hazardous waste.
2. Ensure the batteries are installed correctly with regard to polarity (+ and -).
3. This product is powered by a lithium battery. Due to their small size,
lithium batteries can easily be swallowed by children. Ingestion of such
batteries has been known to cause death.
4. Do not expose light set to moisture.
5. Remove batteries when not used for an extended period of time, or
when depleted.
6. Clean the battery contacts prior to battery installation.
7. The external flexible cable or cord of this luminaire cannot be replaced;
If the cord is damaged, the luminaire shall b destroyed.
8. Dispose of used batteries properly.
9. Use only CR2032 batteries for the remote controller.
10. DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK.
