background image

 
 
 
 

      7. OPERATING INSTRUCTIONS 

 

      

The Anti-Jam Swivel Impellers make a clicking sound as they initially swing into place. This 

       indicates normal operation.

 

 
       A. Remove sink stopper. Turn on a medium flow of cold water. 
 
       B. Turn switch to ON position;, or push your air switch button. Your motor is turning at full speed and   
      ready to use. 
 
      C. Scrape in food waste. Down the drain go table scraps, peelings, rinds, seeds, pits, small bones and 
      coffee grounds. To speed up food waste disposal, cut or break up large bones, rinds and cobs. Large 
      bones and fibrous waste require considerable grinding time and are more easily thrown away with 
      other trash. Do not be alarmed that the disposer slows down while grinding. The disposer is actually 
      increasing torque (grinding power) and is operating under normal conditions. 
 
      D. Before turning disposer off, let water and disposer run for approximately 15 seconds after 
      shredding or grinding stops. This assures that all waste is thoroughly flushed through trap and drain. 
 
      E. It is not recommended to use hot water while running disposer. Cold water will keep waste and fats 
      solid so disposer can flush away particles. 

 

 

8. TIPS FOR SUCCESSFUL OPERATION 
 

       

A. Be sure disposer is empty before using your dishwasher so it may drain properly.  

 
      B. You may want to leave the stopper in the drain when not in use to prevent utensils and foreign   
      objects from falling into the disposer. 

 

Your disposer is ruggedly built to give you many years of trouble free service. It will handle all normal  

Food wastes, but it will NOT grind or dispose of such items as plastic, tin cans, bottle caps, glass, 

china, leather, cloth, rubber, string, and aluminum foil or feathers. 

 

 
9 . CLEANING AND MAINTENANCE 

 

       

 

DO NOT ATTEMPT TO LUBRICATE YOUR DISPOSER! 

 
       

The motor is permanently lubricated. The disposer is self cleaning and scours its internal parts with 

       each use. NEVER put  chemical drain cleaners into the disposer, as they cause serious corrosion of   
      metal  

 
 
 
 

Summary of Contents for ECO CRUSH 400










Reviews: