Home Skinovations Ltd. Silk'n, Instructions For Use Manual

14

Energy Level

Energy level determines the intensity of the Silk’n™ light pulse delivered to your skin, from the lowest level (-) to the highest level (+). 

Corresponding 

I

NDICATOR

 L

IGHTS

 on the 

C

ONTROL

 P

ANEL

represent the increases in energy. As energy level increases, so does hair removal results as 

well as the risk of possible side effects and complications.
Always start your first Silk’n™ hair removal session at the lowest energy setting.
If you experience little or no discomfort during and after the hair removal session using the lowest energy level, raise the energy level by one 

I

NDICATOR

 L

IGHT

 at the next session, and so on for each subsequent session.

Do not raise the energy level if you experience abnormal discomfort during or after treating with Silk'n™!

 (See section 

2.6 - “Possible Side Effects”)

Do not raise the energy level during hair removal session even if you experience no discomfort. Discomfort may also appear 
some time after the session.

Whenever Silk’n™ is turned on its energy level will automatically be reset to the lowest energy level.  Only one 

E

NERGY

 L

EVEL

INDICATOR

 L

IGH

T

 will be on. 

To set the energy level, press the 

E

NERGY

 L

EVEL

 S

ETTING

 B

UTTONS

using “-“ or “+” to respectively decrease or increase the energy level.  The number of 

E

NERGY

 L

EVEL

INDICATOR

 L

IGHTS

 will coincide with the change in energy level.

For your safety, when using Silk’n™ for the very first time, the system is automatically set to deliver the first 50 pulses at the lowest energy level, and 
the next 200 pulses at up to level 3.  
To cancel these safety settings press and hold the “+” and ”-“ 

E

NERGY

 L

EVEL

 S

ETTING

 B

UTTONS

 simultaneously until you hear 2 consecutive “beep” sounds. 

To restore these safety settings press and hold the “+” and ”-“ 

E

NERGY

 L

EVEL

 S

ETTING

 B

UTTONS

 simultaneously until you hear 3 consecutive “beep” sounds.

4.   Using firm pressure, apply the 

A

PPLICATOR

 T

IP

 to the skin. Be sure that the skin area you are about to treat is spread evenly and smoothly, and that the 

A

PPLICATOR

 T

IP

 is in full contact with the skin.

5.   Press the 

P

ULSE

 B

UTTON

 to emit a pulse. You will then see a flash of light and hear a subtle pop-like sound. This is a normal light pulse of Silk’n™.

Note: As this intense pulse may be disturbing to your eyes, it is recommended to close them shortly before 
pressing the 

P

ULSE

 B

UTTON

.

Firmly press the 

A

PPLICATOR

 T

IP

 against the skin

6.   After emitting a pulse, remove the 

A

PPLICATOR

 T

IP

 from the skin. Silk’n™ will recharge for the 

next pulse. 
7.   After approx. 3.5 seconds the 

R

EADY

 I

NDICATOR

 L

IGHT

 will turn on again, accompanied by a beep, to 

indicate that your Silk’n™ is ready for another pulse. 
8.   Continue to administer pulses until the desired skin area is fully treated.

4.4.   Treating with Silk’n™ for the first time

The skin should be shaved, clean, dry and free of any powders, antiperspirants or deodorants.
1.   Press the 

P

OWER

 O

N

/O

FF

 S

WITCH

 to turn Silk’n™ on.

2.   Shortly after pressing the 

P

OWER

 O

N

/O

FF

 S

WITCH

, the 

R

EADY

 I

NDICATOR

 L

IGHT

 will turn on, accompanied by a beep, to indicate that your Silk’n™ is ready 

for its first pulse. 
3.   Your Silk’n™ is automatically set to the lowest energy level.