background image

 

3

Safety Information 

HOMEDEPOT.COM

Please contact 1-877-527-0313 for further assistance.

WARNING:

 To reduce the risk of electrical shock or fire, do 

not use this fan with any solid-state fan speed control device.  
It will permanently damage the electronic circuitry.

WARNING:

 To reduce the risk of personal injury, do not 

bend the blade arms (also referred to as flanges), when 
installing the brackets, balancing the blades or cleaning the 
fan.

WARNING:

 Do not insert foreign objects between rotating 

fan blades.

WARNING:

 

To reduce the risk of fire, electric shock or 

personal injury, mount the fan to the outlet box marked 
acceptable for fan support with the screws provided with the 
outlet box.

CAUTION:

 To reduce the risk of personal injury, use only 

the screws provided with the outlet box.

However, there is no guarantee that interference will not occur 
in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of 
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from   
   that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for  
   help.

1.     To reduce the risk of electric shock, ensure electricity has 

been turned off at the circuit breaker or fuse box before 
beginning.

2.     All wiring must be in accordance with the National Electrical 

Code “ANSI/NFPA 70-1999” and local electrical codes.  
Electrical installation should be performed by a qualified 
licensed electrician.

3.     The outlet box and support structure must be securely 

mounted and capable of reliably supporting a minimum of 35 
lbs (15.9 kg) or less. Use only UL-listed outlet boxes marked 
“FOR FAN SUPPORT.”

4.     The fan must be mounted with a minimum of 7 ft. (2.1m) 

clearance from the trailing edge of the blades to the floor.

5.     Avoid placing objects in the path of the blades.

6.     To avoid personal injury or damage to the fan and other 

items, be cautious when working around or cleaning the fan.

7.     Do not use water or detergents when cleaning the fan or fan 

blades. A dry dust cloth or lightly dampened cloth will be 
suitable for most cleaning.

8.     After making electrical connections, spliced conductors 

should be turned upward and pushed carefully up into the 
outlet box. The wires should be spread apart with the 
grounded conductor and the equipment-grounding conductor 
on one side of the outlet box and ungrounded conductor on 
the other side of the outlet box.

9.     All setscrews must be checked and retightened where 

necessary before installation.

10.   This device complies with part 15 of the FCC Rules. Operation 

is subject to the following two conditions: (1) This device may 
not cause harmful interference, and (2) this device must 
accept any interference received, including interference that 
may cause undesired operation.

        Warning:  Changes or modifications to this unit not expressly 

approved by the party responsible for compliance could void 
the user's authority to operate the equipment.

        NOTE:  This equipment has been tested and found to comply 

with the limits for a Class B digital device, pursuant to Part 15 
of the FCC Rules.  These limits are designed to provide 
reasonable protection against harmful interference in a 
residential installation.  This equipment generates, uses and 
can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful 
interference to radio communications. 

Summary of Contents for 1003 023 399























Reviews: