background image

1

TABLE OF CONTENTS

INTRODUCTION

Introduction ·························································································· 1
Package Contents ················································································· 2
Safety Information·················································································· 3
Preparation ·························································································· 4
Initial Installation  ··················································································· 5
Downrod Mounting ················································································ 6
Circuit Connections  ··············································································· 7
Receiver Installation  ·············································································· 8
Blade Installation ··················································································· 8
Light Installation  ··················································································· 9
Color Temperature Adjustment  ································································· 9
Remote Control Operation ····································································· 10
Troubleshooting ···················································································11
Contact Information···············································································11

Before beginning installation of this product, read the package list on page 2 and ensure all 

parts are present and display no defects. If any part is missing or damaged, contact customer 

service and do not attempt to install the product. Read all of the safety information on page 

3 before installation or use.
Estimated assembly time: 120 minutes
Additional tools required for assembly:

Electrical tape, flathead & Phillips screwdriver, pliers, safety glasses, ladder, and wire strippers

Additional helpful tools:

Electrical Tape, Phillips Screwdriver, Flathead Screwdriver, 11mm Wrench, Step Ladder 

Wire Cutters, Protective Eyewear

Summary of Contents for Merra CFN-1054













Reviews: