Homelite UT10514 Replacement Operator'S Manual Download | Manualshive

Page: 10 / 38

background image

Page 10

WARNING:

Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a second is
sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes result-
ing in possible serious injury.

WARNING:

Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.

WARNING:

Always shut off engine before fueling. Never add fuel to
a machine with a running or hot engine. Move at least
30 ft. from refueling site before starting the engine. DO
NOT SMOKE! Failure to heed this warning could result
in serious personal injury.

WARNING:

If any parts are damaged or missing do not operate this
product until the parts are replaced. Failure to heed this
warning could result in serious personal injury.

WARNING:

Do not attempt to modify this product or create acces-
sories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.

NOTE:  The chain saw has been fully factory tested. It is
normal  to  find  some  slight  oil  residue  on  the  saw.  Read
and  remove  all  hang  tags  and  store  with  the  Operator’s
Manual.

UNPACKING

This product has been shipped completely assembled.



Carefully remove the tool and any accessories from the

box. Make sure that all items listed in the packing list are
included.



Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.



Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the tool.



If any parts are damaged or missing, please call

1-800-242-4672 for assistance.

PACKING LIST

Chain Saw
Scabbard
Combination Wrench
2-Cycle Engine Lubricant
Case (Model UT10516 only)
Operator’s Manual

ASSEMbLy

OPERATION

APPLICATIONS

You may use this product for the purposes listed below:



Basic limbing, felling, and woodcutting



Removing buttress roots

«
...
8
9
10
11
12
...
»

Summary of Contents for UT10514 Replacement







































Reviews:

No comments

Related manuals for UT10514 Replacement

Brand: Makita Pages: 136

Brand: Makita Pages: 30

Brand: Makita Pages: 36

Brand: Makita Pages: 104

Brand: Makita Pages: 32

Brand: Makita Pages: 32

Brand: Makita Pages: 32

Brand: Makita Pages: 28

Brand: Makita Pages: 120

Brand: Makita Pages: 28

Brand: Makita Pages: 40

Brand: Makita Pages: 13

Brand: Draper Pages: 24

Brand: Ribiland Pages: 57

Brand: Partner Pages: 190

Brand: Partner Pages: 256

Brand: Partner Pages: 282

Brand: Stiga Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands