background image

Page 35 

WARRANTY

HOMELITE CONSUMER PRODUCTS, INC. LIMITED WARRANTY FEDERAL AND CALIFORNIA 
EMISSION CONTROL SYSTEMS NONROAD AND SMALL OFF-ROAD ENGINES

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Homelite Consumer Products, 

Inc. are pleased to explain the Emission Control System Warranty on your nonroad or small off-road engine. In California, new small 

off-road engines must be designed, built, and equipped to meet the state's stringent anti-smog standards. In other states, new 

2000 and later model year nonroad engines must be designed, built and equipped, at the time of sale, to meet the U.S. EPA regula-

tions for small nonroad engines. The nonroad engine must be free from defects in materials and workmanship which cause it to fail 

to conform with U.S. EPA standards for the first two years of engine use from the date of sale to the ultimate purchaser. Homelite 

Consumer Products, Inc. must warrant the emission control system on your nonroad or small off-road engine for the period of time 

listed above provided there has been no abuse, neglect, or improper maintenance of your nonroad or small off-road engine.
Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and the catalytic 

converter. Also included may be hoses, belts, and connectors and other emission related assemblies.
Where a warrantable condition exists, Homelite Consumer Products, Inc. will repair your nonroad or small off-road engine at no cost 

to you, including diagnosis (if the diagnostic work is performed at an authorized dealer), parts, and labor.

MANUFACTURER’S WARRANTY COVERAGE:

The 1995 and later small off road engines are warranted for two years in California. In other states, 1997 and later model year non-

road engines are also warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or 

replaced by Homelite Consumer Products, Inc. free of charge.

OWNER’S WARRANTY RESPONSIBILITIES

(a)  As the nonroad or small off-road engine owner, you are responsible for the performance of required maintenance listed in your 

operator's manual. Homelite Consumer Products, Inc. recommends that you retain all receipts covering maintenance on your 

nonroad or small off-road engine, but Homelite Consumer Products, Inc., cannot deny warranty solely for the lack of receipts 

or for your failure to ensure the performance of all scheduled maintenance. Any replacement part or service that is equivalent in 

performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations 

of the engine manufacturer.

(b) As the nonroad or small off-road engine owner, you should be aware, however, that Homelite Consumer Products, Inc., may deny 

you warranty coverage if your nonroad or small off-road engine or a part has failed due to abuse, neglect, improper maintenance, 

or unapproved modifications.

(c)  You are responsible for presenting your nonroad or small off-road engine to a Homelite Consumer Products, Inc., service dealer as 

soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact a Homelite Consumer Products, 

Inc., Customer Representative at 1-800-242-4672.

COVERAGE:

Homelite Consumer Products, Inc. warrants to the ultimate purchaser and each subsequent purchaser that your nonroad or small 

off-road engine will be designed, built, and equipped, at the time of sale, to meet all applicable regulations. Homelite Consumer 

Products, Inc. also warrants to the initial purchaser and each subsequent purchaser that your nonroad or small off-road engine is 

free from defects in materials and workmanship which cause the engine to fail to conform with applicable regulations for a period of 

two years. The 1995 and later small off road engines are warranted for two years in California. In all other states for 1997 and later 

model years, EPA requires manufacturers to warrant non-road engines for two years. These warranty periods will begin on the date 

the nonroad or small off-road engine is purchased by the initial purchaser. If any emission-related part on your engine is defective, 

the part will be replaced by Homelite Consumer Products, Inc. at no cost to the owner.
Homelite Consumer Products, Inc. shall remedy warranty defects at any authorized Homelite Consumer Products, Inc. engine dealer 

or warranty station. Any authorized work done at an authorized dealer or warranty station shall be free of charge to the owner if 

such work determines that a warranted part is defective. Any manufacturer-approved or equivalent replacement part may be used 

for any warranty maintenance or repairs on emission-related parts, and must be provided free of charge to the owner if the part is 

still under warranty.  Homelite Consumer Products, Inc. is liable for damages to other engine components caused by the failure of 

a warranted part still under warranty.
The California Air Resources Board’s Emission Warranty Parts List specifically defines the emission-related warranted parts. (EPA’s 

regulations do not include a parts list, but EPA considers emission-related warranted parts to include all the parts listed below.)
These warranted parts are:  Carburetor, Spark Plug, Ignition, Air Filter, and Fuel Filter.

MAINTENANCE REQUIREMENTS

The owner is responsible for the performance of the required maintenance as defined by Homelite Consumer Products, Inc. in the 

operator’s manual.

LIMITATIONS

The Emission Control Systems Warranty shall not cover any of the following:
(a)  repair or replacement required because of misuse or neglect, lack of required maintenance, repairs improperly performed, or 

replacements not conforming to Homelite Consumer Products, Inc. specifications that adversely affect performance and/or  

durability, and alterations or modifications not recommended or approved in writing by Homelite Consumer Products, Inc., and

(b)   replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled 

replacement point.

The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which 

the engine has been shown to meet Federal emission requirements.  Category C=50 hours, B=125 hours, and A=300 hours.

THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES 
TO MODEL NUMBERS REQUIRED TO MEET THE CARB REQUIREMENTS.

Summary of Contents for UT10532 - OPERATORS







































Reviews: