background image

MAINTENANCE

Make sure the mains supply of the unit is disconnected before performing any maintenance. The maintenance must be carried out by a qualified 

technician and in accordance with local rules and regulations.

Filters of the unit require changing according to the filter change period. When the filters are dirty less air will be supplied by the unit and impact 

the effectiveness of the unit. In areas of high pollution e.g. beside main roads more regular replacement may be required. Filters can be supplied by 

Homevent; part code 021-PIV-W-FILT. Filters should be checked annually or if a drop in ventilation rates are noticed. 

The filter should be checked regularly to determine if it needs cleaning or replacement. External environmental conditions will determine how often 

the filter will need to be cleaned or replaced. Reduced airflow, perhaps accompanied by an increase in noise level, may provide indication that the 

filter needs to be cleaned or replaced. The filter should be inspected and 

cleaned with a vacuum cleaner or replaced as required at intervals 

not exceeding 2 years and always replaced at intervals not exceeding 5 years.

STANDARD CONFORMITY

2014/35/EU Low Voltage Directive (LVD)

2014/30/EU Electromagnetic Compatibility (EMC), in conformity with the following standards:

Electrical Safety: EN60335-1(2012)+A11+A13; EN 60335-2-80(2003)+A1+A2.

Electromagnetic Compatibility: EN 55014-1(2017); EN 55014-2(2015); EN 61000-3-2(2014); EN 61000-3-3(2013).

Year

Required Maintenance

1

Inspect, clean filter if required, dust inside the unit if required.

2

Inspect, clean or replace filter if required, dust inside the unit if required.

3

Inspect, clean filter if required, dust inside the unit if required.

4

Inspect, clean or replace filter if required, dust inside the unit if required.

5

Inspect, replace filter, dust inside the unit if required.

25/02/2020

PIV WALL IOM

Issue:

Saved Date:

A

25/02/2020

PIV WALL IOM

Issue:

Saved Date:

A

25/02/2020

PIV WALL IOM

Issue:

Saved Date:

A

25/02/2020

PIV WALL IOM

Issue:

Saved Date:

A

Summary of Contents for SANO PIV WALL











Reviews: