Honda 08E91-E22-100B Installation Instructions Manual Download

Page: 17 / 22

AII 38215-38958 (0802)

17 of 22

6D01312T

ANTENNA CABLE

TERMINAL

(Connect first.)

FRONT

CONTROL

UNIT

ENGINE STARTER

HARNESS 18-PIN

CONNECTOR

CONTROL UNIT

BRACKET

57. Install the control unit on the control unit bracket.

58. Bundle the excess antenna cable with two wire

ties and secure it with one wire tie to the vehicle
harness.

Installing the Control Unit

56. Connect the antenna cable terminal and the

engine starter harness 18-pin connector to the
control unit.

7401020T

VEHICLE

HARNESS

WIRE

TIE

ANTENNA

CABLE

60. Attach the engine starter label to the back of the

hood.

61. Check that all wire harnesses are routed properly

and all connectors are plugged in.

62. Reinstall all removed parts. Check that all clips

and other fasteners are installed securely. Take
care not to pinch the airbag with a clip during
reinstallation of the front pillar trim. Do not push
the front pillar trim excessively.

63. Reconnect the negative cable to the battery.

Check that the electrical accessory and other
electrical systems function properly.

64. Perform

REMOTE ENGINE STARTER

REGISTRATION

, on pages 18-20, and

FUNCTION

CHECK

, on page 21.

65. Enter the customer’s radio anti-theft code, and

reset the radio station presets.

66. Reset the clock.

59. Using isopropyl alcohol on a shop towel, clean the

area where the engine starter label will attach.

6D01421T

ADHESIVE

BACKING

ENGINE

STARTER LABEL

HOOD

www.collegehillshonda.com

Summary of Contents for 08E91-E22-100B























Search results

Summary of Contents for 08E91-E22-100B

Reviews:

Related manuals for 08E91-E22-100B

Brands by name

Popular brands

Honda 08E91-E22-100B, Installation Instructions Manual

Search results

Summary of Contents for 08E91-E22-100B

Reviews:

Related manuals for 08E91-E22-100B

Brands by name

Popular brands