Honda CD Changer Installation Instructions Manual Download

Page: 9 / 10

AII 23268 (0110)

9 of 10

REAR
BRACKET
STUDS

EPT SEALER

EPT
SEALER

6 x 16 mm
WASHER-BOLT

FRONT
BASE
BRACKET

REAR BASE
BRACKET

6 x 16 mm
WASHER-BOLT

EPT SEALER
(Cut in half.)

FRONT
BRACKET
STUDS

FLANGE
NUTS

38. Cut one piece of EPT sealer in half. Attach the

halves to the rear clip nuts you installed in step
36.

42. Position the CD changer on the studs extending

from the front and rear base brackets, and install
the four flange nuts. Install the CD changer first
on the front bracket, then the rear bracket.

39. Position the rear base bracket on the clip nuts,

and install two 6 x 16 mm washer-bolts. Tighten
the bolts securely.

40. Position the front base bracket on the clip nuts

and install two 6 x 16 mm washer-bolts. Tighten
the bolts securely. Attach one EPT sealer over
the head of the lower bracket bolt.

41. Push the clip of the vehicle wire harness

removed in step 35 into the hole in the rear base
bracket.

VEHICLE
HARNESS
CLIP

REAR BASE
BRACKET

43. Reinstall the relay that was removed in step 20.

44. Plug the BUS cable connector into the CD

changer.

BUS
CABLE

BOLT (reused)

VEHICLE RELAY

CD CHANGER CONNECTOR

CD CHANGER

Summary of Contents for CD Changer











Search results

Summary of Contents for CD Changer

Reviews:

Related manuals for CD Changer

Brands by name

Popular brands

Honda CD Changer, Installation Instructions Manual

Search results

Summary of Contents for CD Changer

Reviews:

Related manuals for CD Changer

Brands by name

Popular brands