Honda HRN536CVKEA Owner'S Manual Download

Page: 11 / 132

ENGLISH

Fallen Leaves

When equipped with the grass catcher, your mower can be used to
pick up fallen leaves for disposal. If using the mower to collect large
amounts of fallen leaves, and not for mowing, adjust the front cutting
height adjustment lever so the front of the mower deck is one or two
settings higher than the rear.
If you want to mulch fallen leaves into your lawn, don’t let the leaf
cover get too deep before you begin. For best results, start mulching
while grass still shows through the leaf cover. In places where fallen
leaves completely cover the grass, remove the leaves by raking, or
install the grass catcher, so your mower can pick them up for
disposal.

Clogged Cutting-means Enclosure

Before clearing a clogged cutting-means enclosure, stop the engine
and turn the fuel valve to the OFF position. With the spark plug cap
disconnected, tilt the mower so the air cleaner side is up.

Clear a clogged enclosure with a stick, not your hands.

Mowing Patterns

Your Honda mower will work most efficiently if you use the following
mowing patterns as much as possible. Mower deck and equipment
design, and the direction in which the cutting means rotate, cause
these mowing patterns to give the best results.

Mulching

Use a counterclockwise mowing
pattern when the Clip Director
lever is in the MULCH position. If
the lawn has an irregular shape,
or many obstacles, divide it into
sections where you can use
counterclockwise mowing
patterns.

Catching

Use a clockwise mowing pattern.
This will give the best Clip Director
and catching performance, leaving
the least amount of clippings on the
lawn.

Rear Discharge Mowing

Remove the grass catcher and
close the discharge guard. Move
the Clip Director lever to the
CATCH setting and begin mowing
in a clockwise mowing pattern. If
the lawn has an irregular shape, or
many obstacles, divide it into
sections.

MAINTENANCE

Good maintenance is essential for safe, economical, and trouble-free
operation. It will also help reduce air pollution and ensure the
emissions performance of the engine continues to be met.

To help you properly care for your mower, the following pages include
a maintenance schedule, routine inspection procedures, and simple
maintenance procedures using basic hand tools. Other service tasks
that are more difficult, or require special tools, are best handled by
professionals and are normally performed by a Honda technician or
other qualified mechanic.

The maintenance schedule applies to normal operating conditions. If
you operate your mower under unusual conditions, consult an
authorized Honda dealer for recommendations applicable to your
individual needs and use.

Remember that your Honda dealer knows your mower best and is
fully equipped to maintain and repair it.

To ensure the best quality and reliability, use only new, Honda
Genuine parts or their equivalents for repair and replacement.

MAINTENANCE SAFETY

Some of the most important safety precautions follow. However, we
cannot warn you of every conceivable hazard that can arise in
performing maintenance. Only you can decide whether or not you
should perform a given task.

SAFETY PRECAUTIONS

• Make sure the engine is off before you begin any maintenance or

repairs. This will eliminate several potential hazards:

– Carbon monoxide poisoning from engine exhaust.

Be sure there is adequate ventilation whenever you operate the
engine.

– Burns from hot parts.

Let the engine and exhaust system cool before touching.

– Injury from moving parts.

Do not run the engine unless instructed to do so.

• Read the instructions before you begin, and make sure you have

the tools and skills required.

• To reduce the possibility of fire or explosion, be careful when

working around petrol. Use only a nonflammable solvent, not
petrol, to clean parts. Keep cigarettes, sparks, and flames away
from all fuel-related parts.

MULCHING PATTERN

CATCHING & REAR-DISCHARGE

PATTERN



WARNING

Improper maintenance, or failure to correct a problem
before operation, can cause a malfunction in which you
can be seriously hurt or killed.

Always follow the inspection and maintenance
recommendations and schedules in this owner’s
manual.



WARNING

Failure to properly follow maintenance instructions and
precautions can cause you to be seriously hurt or
killed.

Always follow the procedures and precautions in this
owner’s manual.