Honda HRN536CVKEA Owner'S Manual Download

Page: 7 / 132

ENGLISH

Engine Oil Level

Check the engine oil level with the engine stopped and the mower on
a level surface.

Use 4-stroke motor oil that meets or exceeds the requirements for API
service category SN or later. Always check the API SERVICE label on
the oil container to be sure it includes the letters SN or later.

SAE 10W-30 is recommended
for general use. Other viscosities
shown in the chart may be used
when the average temperature
in your area is within the
indicated range.

We recommend the use of
Honda genuine oil to maintain
the performance of the emission
control system.

NOTICE

• Running the engine with a low oil level can cause engine damage.

•

Using nondetergent oil can shorten the engine’s service life, and
using 2-stroke oil can damage the engine

1. Remove the oil filler

cap/dipstick [1], and wipe
the dipstick clean.

2. Insert the dipstick into the

filler neck. Do not screw it
down. Remove the dipstick
and check the oil level.

3. If the oil level is near the

low level mark [3], add the
recommended oil to bring
the level up to the high
limit mark [2]. Do not
overfill.

4. Install and tighten the filler

cap/dipstick [1] securely.

Fuel

This engine is certified to operate on unleaded petrol with a research
octane rating of 91 or higher.

We recommend refueling after each use to minimize the air present in
the fuel tank.

Refuel in a well-ventilated area before starting the engine. If the
engine has been running, allow it to cool. Never refuel the mower
inside a building where petrol fumes may reach flames or sparks.

You may use regular unleaded petrol containing no more than 10%
ethanol (E10) or 5% methanol by volume. In addition, methanol must
contain cosolvents and corrosion inhibitors. Use of fuels with content
of ethanol or methanol greater than shown above may cause starting
and/or performance problems. It may also damage metal, rubber, and
plastic parts of the fuel system. In addition, ethanol is hygroscopic,
which means it attracts and retains water in the fuel system. Engine
damage or performance problems that result from using a fuel with
percentages of ethanol or methanol greater than shown above are not
covered by warranty. Using the fuel indicated above is necessary to
maintain the performance of the emission control system.

If your equipment will be used on an infrequent or intermittent basis,
(more than 4 weeks before next use) please refer to the

Fuel

section

of the STORAGE chapter (page 15) for additional information
regarding fuel deterioration.

Never use stale or contaminated petrol or an oil/petrol mixture. Avoid
getting dirt or water in the fuel tank.

NOTICE

Fuel can damage paint and plastic. Be careful not to spill fuel when
filling your fuel tank. Damage caused by spilled fuel is not covered
under warranty.

Remove the tank cap and check the fuel level. Refill the tank up to the
upper limit [1] if the fuel level is low. Refuel carefully to avoid spilling
fuel. Do not overfill; there should be no fuel in the filler neck.

After refueling, tighten the fuel tank cap securely.

Move the mower at least 3 meters away from the fueling source and
site before starting the engine.

Fuel Storage Container

Store your petrol in a clean, plastic, sealed container approved for fuel
storage. Close the vent (if equipped) when not in use, and store the
container away from direct sunlight. If it will take more than 3 months
to use the fuel in the container, we suggest adding a fuel stabilizer to
the fuel when you fill the container.

Air Cleaner Inspection

Remove the cover
[1]. Make sure the
filter [2] is clean and
in good condition. A
dirty air filter will
restrict air flow to the
carburetor, reducing
engine performance.
Refer to page 13 for
air cleaner service.

-20

40°C

-10

100°F

5W-30•10W-30

AMBIENT TEMPERATURE

[1]

[3]

[2]



WARNING

Petrol is highly flammable and explosive.