background image

TECHNICAL & CONSUMER INFORMATION

73

CONSUMER INFORMATION

Replacement Parts, Optional Equipment, and Service Items

Contact an authorized Honda servicing dealer to purchase any of 
these (or other) genuine, original Honda items for your lawn mower.

Replacement Parts

Item

Part Number

Notes

Spark plug

98079-56846

NGK (brand) BPR6ES 

Air filter

17211-ZL8-003

Paper

Lower blade

72511-VH7-000

A torque wrench is required to 
install blades.

Upper blade

72531-VH7-000

Grass bag

81320-VH7-000

Fabric bag only, no frame

Front wheel/tire

44710-VH7-000ZA

HRX217HXA only

44710-VH7-B00ZA HRX217HMA only

Rear wheel/tire

42710-VH7-000

Battery 31500-VH7-B01

HRX217HMA 

only

Spare key

35110-772-013

HRX217HMA only

Optional Equipment

Item

Part Number

Notes

Spark arrester parts

18350-ZL8-000

Arrester and deflector

18356-ZL8-000

ID Plate

90055-ZE1-000

Screw (two required)

Mower deck guard kit

06761-VH7-000AH

Protects the side of the mower 
deck when mowing against curbs

Service Items

Item

Part Number

Notes

SAE 10W-30 engine oil 

08207-10W30

Silicone spray

08209-0001

Lubricates control cable cores

Fuel stabilizer

08732-0001

For long term storage

Matte black touch-up paint 
(aerosol can)

08707-NH105

For handlebar only

Summary of Contents for HRX217HMA























































































Reviews: