background image

20

AVOIDING FUEL-RELATED PROBLEMS

When properly maintained, your Honda lawn mower should provide years of trouble-free operation. This includes the fuel system. However, 

gasoline can quickly deteriorate (in as little as 30 days) causing starting or running problems and, in some cases, damage to the fuel system. 

Most fuel-related problems can be avoided by following the precautions listed below. Fuel system damage and engine performance problems 

resulting from deteriorated gasoline are not covered by the 

Distributor’s Limited Warranty

 (see 

page 22

).

Follow These Precautions to Prevent Most Fuel-Related Problems

During the Normal Mowing Season

Reason

Do not use gasoline containing more than 10% ethanol (E10). Not 

all automotive gasoline is safe to use in your lawn mower.

Higher levels of ethanol in gasoline attract water, and can corrode or 

damage the fuel system and cause performance problems. 

Store gasoline in a clean, plastic, sealed container approved for fuel 

storage. 

Store your fuel supply container away from direct sunlight; if the 

container has a vent, keep it closed.

A plastic container eliminates the risk of rust and metallic 

contaminants from a metal container entering the fuel system.

Gasoline will deteriorate faster when exposed to air and sunlight.

Purchase only enough gasoline to last for 1 to 2 months (about 30 to 

60 days).

If you purchase enough gasoline to last for more than 60 days, add 

a fuel stabilizer to your storage container when you fill it.

Gasoline deteriorates with age so try to avoid storing it for long 

periods, especially in summer heat.

Fuel stabilizer will extend the shelf life of gasoline, but it will not 

reconstitute stale fuel.

Keep your lawn mower’s fuel tank full of fresh fuel when not in use. 

Turn the fuel valve OFF.

If the fuel tank is only partially filled, air in the tank will promote fuel 

deterioration.

Keep the air filter clean and properly serviced. Check it before each 

use.

A properly maintained air filter will help prevent dirt from entering the 

carburetor. The small passages inside the carburetor can become 

blocked.

3 to 4 Weeks Before Next Use

Reason

Keep your lawn mower’s fuel tank full of fresh fuel when not in use. 

Turn the fuel valve OFF.

If the fuel tank is only partially filled, air in the tank will promote fuel 

deterioration.

Turn the fuel valve to the OFF position, start the engine and let it run 

approximately 3 minutes until the carburetor is empty and the 

engine stops. 

The small amount of gasoline in your engine’s carburetor will 

deteriorate faster than the fuel in the fuel tank due to its small 

volume and heat from the engine.

1 to 3 Months Before Next Use

Reason

If you did not add fuel stabilizer to your fuel storage container when 

you filled it up, fill your lawn mower’s fuel tank with fresh gasoline. 

If the fuel tank is only partially filled, air in the tank will promote fuel 

deterioration.

Add fuel stabilizer to the lawn mower’s fuel tank according to the 

stabilizer manufacturer’s instructions. 

Fuel stabilizer will extend the life of gasoline, but it will not 

reconstitute stale gasoline.

Run the engine outdoors for 10 minutes. 

This makes sure treated gasoline has replaced untreated gasoline 

throughout the fuel system.

Turn the fuel valve to the OFF position, start the engine, and let it 

run approximately 3 minutes until the carburetor is empty and the 

engine stops. 

The small amount of gasoline in your engine’s carburetor will 

deteriorate faster than the fuel in the fuel tank due to its small 

volume and heat from the engine.

More Than 3 Months Before Next Use

Reason

Start the engine and let it run long enough to empty all the gasoline 

from the entire fuel system, including the fuel tank. 

Do not allow gasoline to remain in your lawn mower’s fuel tank for 

more than 3 months (about 90 days) of inactivity.

All fuel stabilizers have a shelf life. It is good practice to empty the 

fuel system for long term inactivity.

We recommend Pro Honda Fuel Stabilizer, that has improved formulation with added corrosion protection (

page 21

).

Summary of Contents for HRX217HYAA





























Reviews: