background image

22

EMISSION CONTROL SYSTEM WARRANTY

Your new Honda Power Equipment engine complies with the U.S. EPA, 
Environment Canada, and State of California (models certified for sale in California 
only) emission regulations. American Honda Motor Co., Inc. provides the emission 
warranty coverage for engines in the United States and its territories. Honda 
Canada Inc. provides the emission warranty for engines in the 13 provinces and 
territories of Canada. In the remainder of this Emission Control System Warranty, 
American Honda Motor Co., Inc. and Honda Canada Inc. will be referred to as 
Honda.

CALIFORNIA EXHAUST AND EVAPORATIVE EMISSIONS 

CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and Honda are pleased to explain the exhaust 
and evaporative emissions (“emissions”) control system warranty on your 2022 and 
later Honda Power Equipment engine. In California, new equipment that use small 
off-road engines must be designed, built, and equipped to meet the State's stringent 
anti-smog standards. Honda must warrant the emissions control system on your 
power equipment engine for the periods of time listed below provided there has 
been no abuse, neglect, or improper maintenance of your small off-road engine or 
equipment leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or 
fuel-injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for 
liquid fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other 
associated components. Also included may be hoses, belts, connectors, and other 
emission-related assemblies (see the adjacent column for additional covered parts).
Where a warrantable condition exists, Honda will repair your power equipment 
engine at no cost to you including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE:

The exhaust and evaporative emissions control system on your Honda power 
equipment engine is warranted for two years. If any emissions-related part on your 
Honda power equipment engine is defective, the part will be repaired or replaced by 
Honda

.

OWNER'S WARRANTY RESPONSIBILITY:

• As the power equipment engine owner, you are responsible for the 

performance of the required maintenance listed in your owner's manual. 
Honda recommends that you retain all receipts covering maintenance on 
your power equipment engine, but Honda cannot deny warranty coverage 
solely for the lack of receipts or for your failure to ensure the performance of 
all scheduled maintenance.

As the power equipment engine owner, you should however be aware that 
Honda may deny you warranty coverage if your power equipment engine or 
a part has failed due to abuse, neglect, improper maintenance, or 
unapproved modifications.

You are responsible for presenting your power equipment engine to a 
Honda Power Equipment servicing dealer as soon as the problem exists. 
The warranty repairs shall be completed in a reasonable amount of time, 
not to exceed 30 days.

If you have any questions regarding your emission warranty rights and 
responsibilities, you should contact the Honda office in your region.

YOUR WARRANTY RIGHTS AND OBLIGATIONS

Other States, U.S. territories, and Canada:

In other areas of the United States and in Canada, your engine must be designed, 
built, and equipped to meet the U.S. EPA and Environment Canada emission 
standards for spark-ignited engines at or below 19 kilowatts.
Specific Honda products that do not meet the California emissions regulations can 
be identified by a “California: Not for sale or use” or “California: Only for use in 
Farming or Construction Equipment” decal.

All of the United States and Canada:

The exhaust and evaporative emissions control system on your Honda power 
equipment engine sold in the United States and Canada is warranted for two years 
from the date of delivery to the ultimate purchaser or the length of the Honda Distrib-
utor’s Limited Warranty, whichever is longer. This warranty is transferable to each 
subsequent purchaser for the duration of the warranty period. 
If any emissions-related part on your Honda power equipment engine is defective, 
the part will be repaired or replaced by Honda. All defective parts replaced under this 
warranty become the property of Honda. Only Honda approved replacement parts 
may be used in the performance of any warranty repairs and must be provided 

without charge to the owner. A list of warranted parts is shown in the table below. All 
emission related parts are under warranty for the remainder of the warranty period. 
Normal maintenance items, such as spark plugs and filters, that are on the warranted 
parts list are warranted up to their required replacement interval only.
Honda will also replace other engine components damaged by a failure of any 
warranted part during the warranty period. Honda cannot deny coverage under the 
emission warranty solely for use of non-Honda replacement parts or service 
performed at a location other than an authorized Honda dealership; however, use of 
a part that is not functionally identical to the original equipment part in any respect 
that may in any way affect emissions (including durability) could result in denial of 
coverage. If such a non-Honda replacement part is used in the repair or maintenance 
of your engine, and an authorized Honda dealer determines it is defective or causes 
a failure of a warranted part, your claim for repair of your engine may be denied. If 
the part in question is not related to the reason your engine requires repair, your claim 
will not be denied.

TO OBTAIN WARRANTY SERVICE:

You must, at your own expense, take your Honda Power Equipment engine or the 
product on which it is installed, along with your sales registration card or other proof 
of original purchase date, to any Honda Power Equipment dealer who is authorized 
by Honda to sell and service that Honda product during their normal business hours. 
Claims for repair or adjustment found to be caused solely by defects in material or 
workmanship will not be denied because the engine was not properly maintained 
and used.
If you are unable to obtain emission warranty service or are dissatisfied with the 
warranty service you received, contact the owner of the dealership involved. 
Normally this should resolve your problem. However, if you require further 
assistance, contact the Honda office in your region using the information shown in 
the adjacent column.

EXCLUSIONS:

Failures other than those resulting from defects in material or workmanship are not 
covered by this warranty. This warranty does not extend to emission control 
systems or parts that are affected or damaged by owner abuse, neglect, improper 
maintenance, or unapproved modifications.
This warranty does not cover replacement of expendable maintenance items made 
in connection with required maintenance service after the item’s first scheduled 
replacement as listed in the maintenance section of the product owner’s manual, 
such as: spark plugs and filters.

DISCLAIMER OF CONSEQUENTIAL DAMAGE AND LIMITATION 

OF IMPLIED WARRANTIES:

American Honda Motor Co., Inc. and Honda Canada Inc. disclaim any responsibility 
for incidental or consequential damages such as loss of time or the use of the power 
equipment, or any commercial loss due to the failure of the equipment; and any 
implied warranties are limited to the duration of this written warranty. This warranty is 
applicable only where the California, U.S. EPA, or Environment Canada emission 
control system warranty regulation is in effect.

EMISSION CONTROL SYSTEM WARRANTY PARTS:

American Honda Motor Co., Inc.

Power Equipment 

Customer Relations 

4900 Marconi Drive

Alpharetta, Georgia 30005-8847

Telephone: (888) 888-3139

Email: powerequipmentemissions

@ahm.honda.com

or

Honda Canada Inc.

Power Equipment Customer 

Relations 

180 Honda Blvd.

 Markham, ON, L6C 0H9

Telephone: (888) 946-6329

SYSTEMS COVERED

BY THIS WARRANTY:

PARTS

DESCRIPTION:

Fuel Metering

Carburetor assembly (includes starting enrichment 
system), Oxygen sensor, Throttle body, Engine 
temperature sensor, Engine control module, Fuel 
injector, Fuel regulator, Intake manifold

Evaporative

Fuel tank, Fuel cap, Fuel lines (for liquid and fuel 
vapors), Carbon canister, Canister mounting 
brackets, Fuel line fittings, Fuel strainer, Fuel 
valve, Fuel pump, Fuel hose joint, Canister purge 
port connector

Exhaust

Catalyst, Exhaust pipe, Muffler (with catalyst), 
Exhaust manifold

Air Induction

Air cleaner case, Air cleaner element*

Ignition

Flywheel comp., Flywheel magneto, Ignition pulse 
generator, Crankshaft position sensor, Power coil, 
Ignition coil assembly, Ignition control module, 
Spark plug cap, Spark plug*

Crankcase Emission 

Control

Crankcase breather tube, Breather valve 
assembly, Oil filler cap

Miscellaneous Parts

Tubing, fittings, seals, gaskets, and clamps 

associated with these listed systems.

* Covered up to the first required replacement only. See the Maintenance 

Schedule on 

page 11

.

PWL50975-W

Summary of Contents for HRX217VKAA

























Reviews: