Honda HRX537VKEA Owner'S Manual Download

Page: 18 / 18

ENGLISH

TROUBLESHOOTING

ENGINE WILL NOT START

LOSS OF POWER

VIBRATION

MOWING AND CATCHING PROBLEMS

SPECIFICATIONS

Possible Cause

Correction

Fuel valve OFF

Turn the fuel valve ON (page 5).

Out of fuel

Refuel (page 7).

Bad fuel; mower stored without

treating the petrol, or refueled

with bad petrol

Refuel with fresh petrol (page 7).

Spark plug faulty, fouled, or

improperly gapped

Gap or replace the spark plug

(page 14).

Spark plug wet with fuel (flooded

engine)

Dry and reinstall the spark plug.

Fuel filter clogged, carburetor

malfunction, ignition malfunction,

valves stuck, etc.

Take the mower to an authorized

Honda servicing dealer or refer to the

shop manual for repair.

Possible Cause

Correction

Grass is too tall to cut

Raise the cutting height (page 8), cut a

narrower swath, use a slower ground

speed, or cut more frequently.

Cutting-means enclosure is

clogged

Clean out the cutting-means enclosure

(page 11).

Air cleaner is clogged

Clean or replace the air cleaner

Bad fuel; mower stored without

treating the petrol, or refueled

with bad petrol

Refuel with fresh petrol (page 7).

Fuel filter clogged, carburetor

malfunction, ignition malfunction,

valves stuck, etc.

Take the mower to an authorized

Honda servicing dealer or refer to the

shop manual for repair.

Possible Cause

Correction

Grass and debris lodged under

the cutting-means enclosure

Clean out the cutting-means enclosure

(page 11).

Cutting means loose, bent,

damaged, or unbalanced by

improper sharpening

Tighten loose cutting-means bolts

(page 15).

If cutting means are found to be bent or

damaged, take the lawnmower to an

authorized Honda servicing dealer for

inspection.

Mechanical damage, such as a

bent crankshaft

Take the mower to an authorized

Honda servicing dealer or refer to the

shop manual for repair.

Possible Cause

Correction

Mower is moving too fast for lawn

conditions

Move the Select Drive to a slower

speed (page 9) or push slower.

Cutting height adjustment levers

set at different positions

Set all levers at the same cutting height

position (page 8).

Grass catcher overfilled or

clogged

Empty the grass catcher. Wash the

grass catcher if it is clogged with dirt

(page 15).

Cutting-means enclosure is

clogged

Clean out the cutting-means enclosure

(page 11).

Cutting means dull, worn, or

damaged

Sharpen or replace the cutting means if

necessary (page 15).

MODEL

HRX537C4

TYPE

VKEA

DESCRIPTION CODE

MAGA

GENERAL

Length

1,638 mm

Handlebar height

(Middle position)

1,016 mm

Dry weight

40.

Width

585 mm

Cutting width

530 mm

Cutting height adjustments

19 mm, 32 mm, 46 mm,

62 mm, 75 mm, 88 mm, 101 mm

Grass catcher capacity

85 L

Sound pressure level at

operator’s ears (According

to EN ISO 5395-1:2013)

85 dB(A)

Uncertainty

1 dB(A)

Sound power level

measured (According to

2000/14/EC directive)

97 dB(A)

Uncertainty

0.8 dB(A)

Sound power level

guaranteed (According to

2000/14/EC directive)

98 dB(A)

Vibration transmitted

(According to EN ISO

5395-1:2013)

4.7 m/s

Uncertainty

2.3 m/s

ENGINE

Model

GCV190

Type

4-stroke, single cylinder, vertical shaft, OHC

Displacement

187 cc

Bore and stroke

69 x 50 mm

Cooling

Forced air

Lubrication

Splash and spray

Compression ratio

8.5:1

Maximum speed

2,850 rpm

Ignition system

Transistorized magneto

Spark plug

NGK: BPR5ES

Spark plug gap

0.7 ~ 0.8 mm

Air cleaner

Dry element type

Recommended fuel

Unleaded petrol with a research octane rating

of 91 or higher

Fuel tank capacity

0.93 L

Recommended oil

SAE 10W-30, API SJ or later

Engine oil capacity

0.55 L

* Refill amount: 0.35 ~ 0.40 L

* Actual amount will vary due to residual oil in the engine. Always use the

dipstick to confirm the actual level (see page 6).

DRIVE

Type

Variable speed Select Drive

Engine to transmission

V-belt

Main clutch

Slipping friction cone type

Mower speed

(engine @ 2,850 rpm)

0 ~ 1.64 m/s

–100

Summary of Contents for HRX537VKEA



















Search results

Summary of Contents for HRX537VKEA

Reviews:

Related manuals for HRX537VKEA

Brands by name

Popular brands

Honda HRX537VKEA, Owner'S Manual

Search results

Summary of Contents for HRX537VKEA

Reviews:

Related manuals for HRX537VKEA

Brands by name

Popular brands