background image

9

ENGLISH

Sliding Door Position   

The sliding door [2] can be positioned to produce different mowing 

results. If the preferred sliding door position is unknown, install a 

grass catcher and begin mowing with the Clip Director knob [1] all the 

way to the catcher position. Check the appearance of the lawn. As the 

knob is moved towards the MULCH position, more grass will be 

recycled back into the lawn. Adjust the Clip Director knob until the 

desired result is achieved. 

Rear Discharge   

To discharge clippings to the 

rear, remove the grass catcher 

and position the Clip Director 

knob [1] in the catcher range.

Maximum rear discharge 

will occur when the Clip 

Director knob is all the way 

to the left (catcher) 

position. As the Clip 

Director knob is moved 

toward the right (MULCH) 

position, less grass will be 

discharged though the rear 

cutting-means enclosure. 

Are You Ready to 

Mow?

Be sure to wear protective clothing. Long pants and eye protection 

can lower your risk of injury from thrown objects. Wear footwear that 

protects your feet and won't let you slip if you mow on slopes or 

uneven ground.

OPERATION

MOWING PRECAUTIONS 

Before operating the mower for the first time, please review 

SAFETY 

INSTRUCTIONS (

page 2

and

 PRE-OPERATION CHECKS (

page 5).

Even if you have operated other mowers, take the time to become 

familiar with how this mower works, and practice in a safe area until 

you build up your skills.
For your safety, avoid starting or operating the engine in an enclosed 

area such as a garage. Your mower's exhaust contains poisonous 

carbon monoxide gas that can collect rapidly in an enclosed area and 

cause illness or death.

FREQUENCY OF USE

If your equipment will be used on an infrequent or intermittent basis, 

(more than 4 weeks before next use) please refer to the 

Fuel

 section 

of the STORAGE chapter (page 17) for additional information 

regarding fuel deterioration.

STARTING THE ENGINE 

1. Turn the fuel valve [1] to the ON position.

[1]

[2] (50% open)

CATCHING OR REAR DISCHARGE 

AND SOME MULCHING

[2] (fully closed)

FULL CATCHING OR

REAR DISCHARGE

FULL MULCHING

[1] (catcher position)

[1] (MULCH position)

[2] (fully open)

[1] 

ON

[1] 

Summary of Contents for HRX537VKEA



















Reviews: