NOTE
o
No. 1 carbu retor is the base carbu retor.
Fuel
o
Before tightening the carbu retor connecti ng bolt/nut, check there is no cleara nce between each of the carbu retor
joints.
o
Tig hten the each connecti ng bolts/nuts g rad ually and alternately, be sure the bolt thread projections a re equal
high. Hold the n ut and tighten the other n ut on other side.
Requisite Service
o
Carbu retor removal/i nstal lation (page 5-4)
Procedure
Assemble No. 2 carb. with No. 1 carb.
( 1 ) Th rottle l i n k
( 2 ) No. 2 carbu retor
(3) Carbu retor connecting bolt
Assemble No. 3 carb. with No. 1 /2 carb.
(4) Starting enrich ment valve link assembly
(5) Fuel tube/joint pi pe/0-ri ng
(6) Center collar
(7) Rea r collared dowel pin
(8) Front collared dowel pin
(9)
No.
5
vacuum tube (to the No. 1/2 craburetor)
( 1 0) S u b-ai r joint pi pe/tube/0-ring
( 1 1 ) No. 6 vacuum tu be/joint pipe/0-ring
( 1 2) No. 5 vacu u m tube (to the No. 3 carbu retor)
( 1 3) No. 3 carbu retor
( 1 4) Thrust spring
Assemble No. 4 carb. with No. 1 /2/3 carb.
( 1 5) Choke cable holder
( 1 6) No. 4 carbu retor
( 1 7 ) Thrust spring
( 1 8) No. 5 vacuu m tube (to the No. 4 carbu retor)
( 1 9) Carbu retor connecti ng n ut
(20) Return spring
(21 ) Plastic collar
(22) Starting enrichment valve a rm
(23) Plastic washer
(24) Starting en richment valve arm screw
(25) Choke cable
(26) 0-ri ng
(27) Air cham ber/a i r fu nnel
(28) Lock plate
(29) Air cham ber screw
Q'ty
1
1
3
1
2/3/6
1
1
1
6/3
2/1/4
2/2/4
1
1
1
1
1
1
1
6
2
4
2
4
4
1
4
4/4
4
1 2
o
Carbu retor synchronization (page 5- 1 4)
Remarks
Refer to the d rawing for the combination of the washer.
California type only
California type only
California type only
CAUTION
o
Tighten each nuts gradually and alternately with the
above procedure. Do not over-tighten the nuts.
5- 1 1
Summary of Contents for Magna VF750C
