English |
9
Robotic Lawnmower
Unit
Miimo HRM40
Docking station
Input voltage
VDC
24
Power consumption charging/perimeter wire switched on
W
55/2 .6
Charging current (up to)
A
2 .3
Allowable charging temperature range
B)
°C
5–45
Weight according to EPTA-Procedure 01:2014
kg
1 .65
Protection type
IPX4
Power supply unit
Switzerland
80016-Y0E-003X
United Kingdom
80015-Y0E-003X
Rest of Europe
80014-Y0E-003X
Input voltage (AC)
V
220–240
Protection class
/ II
Frequency
Hz
50–60
Output voltage (DC)
V
24
Protection type
IPX7
Weight
kg
0 .8
A) Depends on cutting height, grass conditions and moisture
B) Internal battery temperature
The specifications apply to a rated voltage [U] of 230 V . These specifications may vary at different voltages and in country-specific models .
Noise/Vibration Information
Noise emission values determined according to
EN 50636-2-107
.
Typically the A-weighted noise levels of the product are:
Sound power level
61
dB(A) . Uncertainty K =
2
dB .
Explanation of Figures
Action
Figure Page
Accessories
A
22
Delivery scope/unpacking the
mower
B
23
Laying out perimeter wire
C
23
Extending perimeter wire
D
24
Laying perimeter wire around new
inner object
E
24
Lifting up and carrying the mower
F
25
Setting the height of cut
G
25
Place & Mow
H
26
Adding a further lawn area
I
26
– with additional docking station
(right)
– without additional docking station
(top left)
Cleaning
J
27
Maintenance
K
27
Installation
Check if the perimeter wire is fully pegged
to the ground avoiding any slack lengths of
wire . Any loose wire can be a trip hazard .
Remove straw, stones, loose pieces of wood, wire, live
mains cables and other foreign objects from the cutting
area . Make sure that the cutting area is even and has no
ditches, grooves and steep slopes above 15°/27 % that
are clear obstructions for the mower .
The docking station must be positioned on the wire at an
outer edge of the cutting area . It may not be positioned
on the side of a tool or garden shed standing as an island
within the lawn to be mowed .
It is recommended that you mow your lawn once with a
conventional lawnmower before installing and before the
first mowing of the new season and whenever the grass
clippings would be longer than 5 mm .
The mower’s cutting system is designed to cut small
lengths of grass (30–50 mm) . The clippings can remain as
mulch to fertilize the lawn . The height of cut for mower
can be adjusted to 30, 40 and 50 mm .
For the first few weeks of usage, set the height of
cut to 50 mm to prevent the perimeter wire being cut .
Afterwards, the wire will be covered by the lawn .
Additional perimeter wire can be added using a wire
connector (see figures
D–E
) .
The perimeter wire can be extended up to a maximum
length of 250 m .
Summary of Contents for Miimo HRM40
